Categories
bodywork mechanics paint

The Setbacks

Since August 2023, it had been a trying time with one thing and another, with all available finances being directed to the daily driver cars. Trying to invigorate motivation over Christmas, I sought to work on cleaning the CV joints and putting on new CV boots. Dismantling the joints was reasonably simple and while messy, not too difficult to clean over a period of days. Ball bearings from one CV joint had signs of wear (a blue-ish tinge) and the other 3 seemed good. However, re-assembly of the good CV joints with their corresponding ball bearing and bearing cages proved to be quite difficult. They wouldn’t just slip back in to place without a bit of force required and then only one of the CV joints remained supple, so I think dismantling and a re-assembly will be on the cards, failing that, I buy a new set of 4 CV joints and be done with it.

Roll around to February 2024 and the mis-haps continued. The weather was nice and I felt I could take on the quick task of respraying the engine bay in bright white to fix the overspray error from last year. Through January over a few weeks I filled some minor holes and gaps in the engine bay area and prepped in readiness for painting.

Set back number 1: I damaged, beyond repair, the new spray gun bought last year by over tightening a BCP coupling.

Set back number 2: In my haste to make do with the other spray gun, I didn’t get my mixing ratios right (hindsight) by misreading the ratios on the measuring cup.

Set back number 3: Because of the messed up ratios the paint was too thin and the spray gun pattern was all over the place. Paint coverage was poor with runs and pooling of the paint, it was time to stop and clean up the mess. Subsequently, the area was later re-rubbed down in readiness for another attempt when I felt confident and ready to tackle it again.

Engine bay rubbed back down after the disastrous attempt at painting
Engine bay rubbed back down after the disastrous attempt at painting
Categories
bodywork paint painting

A little more primer

By the end of May I had plopped on some more filler to smooth out a few bumps and high spots, mainly on the rear valence and engine bay aperture. I also added some filler to sort out the minor corrosion on the rain gutter on the right side (UK drivers side) above the door. I spent a few on/off days of May into June, rubbing back the filler on the rain gutter repair, rear valence and other small areas on rear portions of the body. I was beginning to think the body was now in the final stages of near completion, but I still have plenty of filler if needed. Around this time I visited Paul at South Coast Customs and he had a 1966 Beetle that he was restoring but was taking it back to bare metal first. The filler on that car was 5-10mm thick on the lower rear quarter panels and hid a multitude of poorly executed repairs, something I wanted to avoid this car in having too much filler.

At the end of this stage I was considering the options of installing a third brake eye, behind the cooling grills above the engine compartment. There was a mixture views on the Volkszone forum, especially cutting into the metal work beneath the rear window to insert a removable plate with an after market LED brake light fitted. With the 1302S being a relatively scarce Beetle these days, I had begun second thoughts on making a cut out under the rear window to insert the 3rd brake eye and started to consider a self adhesive LED light strip instead.

My other question to the forum was whether I should grind off or keep the tar board hooks on the engine bay firewall – I didn’t need much convincing… I decided to grind off the tabs which in doing so was sending an unmanageable shower of sparks that were getting everywhere all over me. I resorted to knocking them off with my spot weld chisel and then grind back with a flap disc, far less sparks flying all over the place. The only problem with knocking off the spot welds was that it created two more holes in the fire wall that I will have to fill or cover up.

I laid a (fourth) coat of primer on the rubbed down areas and the engine firewall looked a lot neater with the tar board tags having been removed. The rear valence was repainted and other smaller parts like the fuel filler flap and engine lid hinge mounts were painted in primer as well.

Categories
bodywork paint

1st Coat of Primer

Easter Sunday (April 2023) and I took the plunge for my first attempt to apply a coat of primer with the spray gun. The work space around the Beetle was tidied, cleared of obstructions and covered up and I had set up the compressor with the new air hose line for better air delivery to the spray gun. The next step was to mix up the primer paint, I had tried out on the Corsair last year, with questionable results. The measuring cup made things quite easy with appropriate markings for the proportional amounts I needed for the primer, hardener of 4 to 1 with 15% thinners. I used a tip, from the internet, of covering the edge of the tin with foil to make pouring of the primer a bit more controlled and a cleaner experience, and it worked fairly well.

With the mixture ready and added to my used spray gun which came with the compressor, obtained last year, I started to spray. Well, more like it spat the paint out as if it were silly string. Luckily I had a clean unused spare from the same source as the compressor and I transferred the paint to the new gun. The paint came out as it should and I set to painting the interior first. All was going well and I mixed up a second batch to continue with the exterior, spare wheel well and engine bay.

On the whole I was pleased with my efforts with the primer giving a good smooth and even finish masking the different layers of filler and flattened original paint. I could now see where more filler would be required to even out the low/high spots and touch up the rough or uneven areas.

Categories
bodywork floor pan suspension

Body work and prep

March 2023 saw me make more progress on the Beetle’s body work by the way of a 3rd or 4th round of filling, sanding and cleaning up with more filler on the original 1997 repairs. I also got to flat off the spot welds around the front cowl at bonnet opening and front valance and I completely removed the wiring loom, replaced with rope guides for the future re-install of a new loom.

The floor pan had been rolled out on to the driveway so it could be cleaned up and where there was the space to attach the anti roll bar with new poly bushes. I had to enlarge the roll bar clamps bolt holes a while ago as I think my original clamps disappeared on the strip down (June 2021) while at Pauls. Fitting the new polyurethane bushes, washer and nut combinations was not as easy as I thought it was going to be. Not enough of the roll bar thread protruded past the poly bushes for the retaining washer and castle nut to get a purchase. So, I had to hit the bushes with a soft mallet to get them pushed in enough to enable me to fit a thinner washer and nut to press the bush in further. I then had to swiftly remove the nut and washer, then quickly put on the large retaining washer and nut to tighten up before the bush expanded again.

I made a short video walk around, however, the audio and commentary isn’t very good, but you should get the idea.

There were a couple of more items to come out of the beetle shell one of which was the wiring loom and I used some rope to attach to an end in the engine bay. This was so I could pull through the rope that would then stay in place for the later re-install of a new wiring loom. The other was the glove box door and I also took off the engine lid hinge mounts to allow easier access to clean up the engine bay firewall.

With 320 grit paper on an orbital sander I sanded the sides of the car shell up to the rain gutter to flatten off the existing paint and remove other minor blemishes. The dashboard was treated the same to flatten off the gloss paint, smooth out minor blemishes and act as a matt surface for, hopefully, better primer adhesion. I also treated the the engine bay firewall the same way and along with a small block with 320 grit sand paper which also cleaned off some the ingrained grease and dirt. I left the ‘tar board’ hooks in place in case I wanted to put one of those back in at a later date.

The next big step is to get some high build primer on the inside and outside of the body. This should highlight the areas requiring more work for filling and rubbing down. It’s a big step and I will be taking my time preparing the workshop to allow me more space to move around the body and masking off areas that won’t need the primer.

Note: no ChatGPT here, all my own words.

Categories
bodywork brakes

Brake Master Cylinder

After a year of waiting, I finally got around to sending my brake master cylinder for refurbishment in January/February 2023. As the pictures show, it was in a sorry state after sitting unused for over 27 years, causing it to dry out and deteriorate.

Initially, I considered buying a brand-new RHD master cylinder, but the cost of £200+ made it a less appealing option. Instead, I decided to opt for refurbishing my original one with a stainless steel inner sleeve, new seals, and black powder coating. The entire process was carried out by Past Parts, a reputable company based in Bury St Edmunds, UK, and took about two weeks to complete.

In the end, the cost of the refurbishment was less than £150, including all postage fees, allowing me to save a significant amount of money. This saving will be put towards purchasing new German brake circuit warning switches, which I hope to acquire soon.

Overall, I am pleased with the outcome of the refurbishment, and I’m glad that I opted for this option rather than buying a new part. It’s a great feeling to see my old brake master cylinder come back to life after so many years.

While I was in the workshop on a relatively mild day, I took the opportunity to do some body filler work. I started by sanding down the front right side quarter filler using 80 grit paper, before adding some more filler to the lower door ‘A’ posts to smooth out the lip from repair work done in 1997.

Last year, I spent some time researching how to work with automotive body filler and came across Bad Chad’s YouTube channel. His long but detailed video on filling and sanding techniques was particularly helpful, and I used his guidance to achieve decent results on the rear quarter panels. I also had some insightful conversations with John, a friend who restores classic cars and has worked on my Ford Corsair, as well as with Paul from South Coast Customs over the Christmas period. John offered to give me a hands-on tutorial on filling, sanding, and prepping for primer and paint in the spring, depending on his workload.

Recently, I discovered another YouTube channel by a British customizer named Paul Bacon. I was impressed by his straightforward, no-nonsense approach to bodywork and appreciated his creative style. His work, including the epic Automatron custom car, inspired me to continue learning and improving my skills. You can check out one of his videos below.

Note: This blog was written with the help of ChatGPT. The original blog post can be seen here.

Categories
bodywork chit chat floor pan

Minor jobs

Dec 2022 – Jan 2023: Stripping out the dash, the wiring and finally removing a stubborn steering column were the last of the jobs to reduce the body shell down to a… shell. The wiring loom was left in place as I hadn’t found any suitable cord or cables to re-route and pull it through to maintain a method for replacing with a new loom, in the future.

One job that I was keen to get done was to ensure the left and right handed Bakelite heater tubes that mount through the rear cross member were in position with the holes drilled for mounting. It turned out the oval holes were not big enough for the Bakelite heater tubes and I had to grind out the ovals. Luckily I had a Dremel (4000) with a couple of grinding attachments, one of which broke 3/4 of the way through the job on one of the apertures. It took over an hour of careful grinding on each side for the tubes to fit flush and enable me to mark up and drill the holes for the mounting bolts. The heater branch pipes were mocked up and fitted well which began to make things were moving in the right direction.

The bolts will need to be welded to the cross member, as per on the original panels which would make installation of the heater pipes much easier when the body is back on the floor pan. By mid January 2023, It got very cold (sub zero) and enthusiasm waned for the remainder of the month.

Categories
bodywork paint

Schultz Gun Painting (Cobra Bedliner)

November 2022 and with the earlier jobs done I could take a closer look at the bodywork in some more detail. It had been on my mind for some time but I was keen to try out the Cobra Bedliner I had bought back in March 2022. It all looked simple on the video I watched a few times and in reality the process of mixing and application was not difficult, though a bit messy.

I approached the task in two stages, the rear end was to be first as it was more accessible with less prep work required and the front was to be the second stage, requiring more preparation and other minor jobs.

For the second stage on the front end, I needed to clean up the excess welds, unwanted previous black undercoat, weld up some minor holes and fit a brake pipe bracket on the front right inner wheel arch. I hadn’t attempted welding on bodywork since those disastrous days way back in 1996. It took a few attempts to securely weld the bracket and plug the holes in the wing arch mounting areas but in the end all turned out OK.

The overall experience of applying the Bedliner was OK and not as difficult as I first thought it was going to be. I tried my best to take my time and not rush things. Measuring the 2K bright white paint from the tin into the measuring pot (roughly) was probably the most messy part of the process. I seemed to hurry myself spraying, thinking the Bedliner would start to dry in the Shultz gun before I could finish, and if I had been slower I probably would have made a better job of coverage on the underside areas. I used two bottles of the Cobra Bedliner, one for each end of the car and I have a third that I intend to use on the floor pan, underside and touch up on the body where needed.

December 2022 – The weather took a turn for sub-zero temperatures and work stopped for a short period.

Categories
bodywork brakes

Fettling

During October 2022, one of the other little jobs that had hung over me for the most part of 12 months was to finish off the brake lines for the rear. During the summer, I had found on eBay nearly new, flexible brake pipes for the front and rear and finally ordered from Amazon some male/female 10 mm brake pipe unions. I already had some 6 mm copper brake pipe left over from when I had done my Ford Corsair brake lines a few years ago. The pipes were made up and flexible hoses were fitted but only loosely tightened as they didn’t have any fluid in them. The master cylinder was still at this point needing to be sent away for refurbishment.

Having dabbled with filler and satisfied myself that there was a fair bit of work to be done I turned my attention to other parts of the car. If I was going to go the whole hog of a full body repaint then I needed to strip the body shell of more items. First was the headliner, which I kept for future refitting reference. Next was removal of door latches, interior light, dashboard instruments and switches. Removal of the dash instruments wasn’t too difficult, but putting it back together maybe something of a nightmare. I also removed the wiper mechanism along with the wirng loom, which was a birds nest of a mess as the plan is to renew it.

With the dash stripped out I could look at the body work side of things in more detail. One job that again had been hanging around in my head was the removal of the seal retaining strip that would have held the bonnet rubber. Paul had suggested that I go the Mexican Beetle method of the rubber that attaches to the bonnet and engine lid for a cleaner finish. So with a new spot weld chisel I set to breaking off the spot welds and had the retaining strips removed in a relatively short space of time. The remnants of the spot welds just needed to be ground flat and smoothed. I doubt the car (if/when finished) will see much of the rain when used, especially if the new seals (when fitted) aren’t very good.

The front valence had taken a bit of a battering when the body was being removed from the floor pan way back in June 2021. Paul had knocked out the worst of the dents and deformation before returning the body to me but I had a go with my planishing hammer and dolly to re-shape it some more. The result was an improvement and the first time that I had done such panel beating. The surface will be finished with filler.

One of the last jobs, prior to doing the Bedliner job (next post), was the very dusty task of cleaning up the rear luggage area from the remains of old insulation and sound deadening materials. I used a cupped wire brush and a knotted wire wheel on my angle grinder. It meant it was a clean area ready as a practice area for trying out primer and painting colour, later on. On the rear lower cross member with the large oval holes, these would accommodate the heater pipes from the engine. Captive nuts would need to be welded around these vent holes before any attempt at primer spraying would be done. I acquired from Paul a couple of vent pipes that had gone missing as replacements and to act as templates to sort his out.

Categories
bodywork

… some time later

Talk about taking my time. My main excuse for the long break was that from March to August 2022 we had goose eggs being incubated and then the single success of a hatched gosling was growing up in the workshop that housed the beetle. The gosling (Ashley) took up a fair amount of space so working on the beetle just couldn’t happen. At least, with some assistance, I had got the body shell up on to the trestles which I had made at the end of November 2021, therefore I could roll and store the floor pan underneath.

Way back in March 2022, I bought a 3 litre tin of 3M filler with hardener, 5 litres (with hardener) of high build primer, 5 litres of thinners and 3 Cobra Bedliner systems (anti stone chip) to use with a Schultz spray gun. Roll on September 2022 and I had the space to work on the body shell and my first job was to try out the filler on the rear quarters.

The body filling was done over several days with the first layer being rubbed back initially with an orbital sander and 80 grit paper to expose the low points. A second layer was applied and rubbed back by hand to reveal the low spots again and thus a third layer was applied and though an improvement there were still low spots after a combination of orbital and hand sanding. Having seen something on YouTube, I bought some better filler spreaders as the plastic applicator (vinyl applicator) I had been using was too stiff and not giving any flex to follow the body shape.

After the third filling and rubbing down attempt I decided to stop and seek some assurance by speaking to Paul before I went any further. I had by then got a reasonable idea for filling and trying the techniques of rubbing down with different grades of paper – I just needed to take my time therefore turned my attention to stripping the car down to just a shell.

Categories
bodywork welding

The Body Shell

November 2021: With the semi-rolling floor pan returned home, Paul had the body shell to work on. By the time I went back to his workshop to help out, a couple of weeks later, he had already replaced the rear bumper bracket mount, repair sections so as to get it up on to a rotisserie. He had also formulated the rudimentary set up for the removable rear valence. The removable rear valence would greatly assist in the installation and any future removal of the engine.

With the bumper mounts repaired, attention was to look at the quarter panel repairs previously done in 1997. It was apparent that the welding on both sides were of varying quality (possible by two different people) and the repair panels overlapped the old metal by a large amount. The right side (UK driver side) was the worst with deformation and warpage and Paul felt it was best to cut the whole rear quarter out and replace it with a new panel. The left side wasn’t too bad but Paul trimmed the excessive overlap on the 1997 repair and welded it in further down the existing original rear quarter meaning less filler would be needed to cover the repair.

With some strength back in the body, Paul set to work on the right inner rear wheel arch repair with the body mounting bracket. A large repair section had been purchased by me earlier in the year and judging by the pictures it seemed this was a relatively straight forward job.

A not so simple job, was the replacement and widening of the front firewall. The (cheaper Klokkerholm) panel I had supplied meant Paul spent quite a bit of time cutting and fabricating this up to be right, along with a front left strut repair. As for me, I was grinding down the welds on the earlier jobs done by Paul as well as cleaning up the underside of the rear body and painting all the exposed metal in red oxide primer.

Some more images to show the work that was done. The pile of removed metal was quite substantial and there were layers upon layers of repair patches – that should save a bit of weight.

By the end of November, the 1302 body shell was returned home and put alongside it’s floor pan.