Categories
bodywork

Preparation begins

By March 2021 I had begun to take a closer look at the areas I thought would require repairs. Armed with an angle grinder and a knotted wire brush attachment, I started in the right hand side rear wheel arch. As I ground away behind the black under seal there was a lot of filler which covered up a multitude of repairs. The body to chassis mounting point was badly corroded and around the wing mounting there was a lot of hidden rust holes – it wasn’t looking very good. More work was required on the left side front inner wing and suspension strut tower. On the right hand side by the brake master cylinder there was body to floor pan welding as well as in the drivers side foot well and on both sides the floor to bulk head bolts had been welded over.

As I worked my way around the car I seem to open up many areas that needed further investigation, all these old repairs and fixes, are probably what saved the car from being an MOT failure in the past and then being scrapped. In the meantime, I had messaged Paul at South Coast Customs & Classics a few times to check on the timeline of when he could take the Beetle in to this workshop but also to invite him to come over and take a closer look at the car. By April (2021) I was becoming rather despondent and wondering if it was really worth continuing as the repair list was getting longer and possibly out of my financial reach.

After Paul’s visit at the end of April, his confidence and enthusiasm to do the repairs to the car was very reassuring and went a long way in securing my decision to continue and go for an all out restoration – though not to any concourse standard. I continued to collect more panels for the repairs prior to when Paul could take the car in to his workshop. The final project list I drew up is shown below (June 2021 Version 3)

Categories
bodywork chit chat pedals

Runners and Pedals

The financial situation had eased which helped fire up the enthusiasm with the Beetle in the spring of 2008. The covers were removed to reveal the Beetle was fairing well in the car port under a tarpaulin. At some point, Grey zinc primer had been applied to the surface rust that was appearing on the repairs done in 1998.

A pair of correct style seat runners were purchased as the new floor that had be done 10 years previously had the wrong type. I also bought a new accelerator and clutch cable as well as some foot pedal spare parts. There is not any photo graphic evidence, but I replaced the seat runners by drilling out the spot welds on the existing runners and successfully welding in my new ones. My welding had improved (albeit some what agricultural) since 1996, as I had built this dragster for my then young son for a carnival.

By early summer 2008 and I had the foot pedals with other associated parts powder coated in readiness for installation. The powder coater had unfortunately painted over some areas that needed to be clear of paint and a fair bit of rubbing down was required so it would all fit together and operate smoothly. Installation was tricky but I had to drill holes in the new floor to weld captive nuts on the underside so I could bolt down the mounting bracket for the whole assembly. I welded the accelerator pedal bracket to the floor, it was not pretty but functional. Fitting the clutch cable was nigh on impossible even with guidance in the Beetle bible (How To Keep Your Volkswagen Alive) so I left that for another time.

Categories
bodywork Buying chit chat

The Resto Begins

Back in August 1995, at our rented garage (lock up), the wife and I had stripped the car down so we could assess the way forward. It had become apparent that a few more welding jobs would be needed. By the summer of 1996 I had been preparing to work on the Beetle so had purchased a SIP350 Turbo welder, associated accessories and sheet metal to tackle the body work that required repair. Some new panels comprising of a semi-W engine lid, matching rear valance and a pre ’67 front valance had been purchased to fire the imagination from URO in Bournemouth. We had also purchased a small car trailer to move the Beetle about.

newspaper stuffed in the ‘A’ posts

We took the beetle around to my ‘in-laws’ home to work on in their garden as they had a fair amount of space and it was easier to get electric to as well. A closer inspection was revealing a myriad of issues of old repairs over old repairs and in dire need of repair. It’s true, I found newspaper stuffed in the ‘A’ posts from an Essex publication after I had chipped away a bodge of filler around the lower door hinges, on both sides. A DVLA vehicle history search, that I later obtained, revealed it had spent some time in Billericay, Essex in the mid 1970s.

It didn’t occur to me to seek repair panels for these sections, being the complete novice at this body work business I was trying to make my own patches out of sheet metal. I took instruction from various members of the family trying out my new MIG welder but I was mainly blowing holes in the bodywork and new steel creating a fair amount of spatter welding. The advice being dished out wasn’t really helping me make a decent job of this and my patch work of repairs were bloody awful. I was too afraid of cutting too much out and ruining the structural strength of the vehicle.

The end of that week in August 1996, I became very aware I had bitten off more than I could chew on this project and the car was wheeled away and put back into it’s garage for another long stint of storage.