Categories
bodywork brakes paint

Summer Jobs 2026

I had been busy on and off with various jobs on the Beetle. The first priority was to finish plumbing in the brake system now that the body was back on. I’ll say it now: fitting the pipework from the brake fluid reservoir to the master cylinder was, so far, probably the most frustrating and awkward job I have had to do on this little car.

From getting the bends in the pipes in the right places, fitting the correct amount of braided rubber hose, to eventually removing the master cylinder so I could push-seat the pipes properly, it was all a bit of a faff. In the end, I assembled around two-thirds of the system on the bench, including the master cylinder, and then made the final connections between the fluid reservoir and the remaining third of the pipework under the car at the bulkhead.

With all the pipework connected, and with some trepidation, I put in the brake fluid. Then some more, and then some more… until I noticed a leak at a joint on the frame head, which I duly tightened up.

I then noticed two large puddles of brake fluid at the rear.

When I first installed the brake lines back in September 2021, I hadn’t tightened them up. So, typically, now that the body was back on, the leaks were in awkward places above the torsion tube, at the ‘T’ joints in the pipes, as well as from both rear bleed nipples. After tussling with the awkward access to the brake-line fittings, I eventually got everything tightened up and the system stopped leaking. The rear brakes, however, still needed adjusting.

Hot weather arrived during May and the next job was to remove the engine tins ready for refurbishment. The only one I couldn’t remove was the panel behind the main crank pulley, as I didn’t have a 36mm socket.

Cleaning the engine tins and ‘doghouse’ fan shroud was a filthy job, covering both myself and much of the workshop in dust. Thankfully, I was wearing a face mask, so I didn’t get too much of it up my nose!

With the tins back to bare metal, I treated them with Jenolite, a rust-converter treatment in an aerosol.

With the hot weather continuing, I decided to turn my attention to the doors, as both needed a bit of attention due to rust appearing along their lower edges. Dismantling them was made much easier after watching a YouTube video by “Slades VW Beetle“. The process was quite straightforward, and with a bit of care it was easy enough to follow the steps in the video.

Stripping the doors back to bare metal was another hot and dirty job, once again plastering the workshop, and everything in it, with a layer of dust. I treated the exposed bare metal with Jenolite, including those awkward-to-reach areas.

There were a few previous rust repairs that I removed, which exposed a few more holes, but thankfully not too many. In fact, the doors were actually in pretty good order. They are clearly replacement doors from a previous restoration, judging by the evidence of their previous colour on the inside panels.

I went to see Paul (and Ash) during this period and, while the main purpose of the visit was to arrange a timeframe for the engine strip-down, I also took the opportunity to get some ideas on repairing the doors.

Welding would have been an option, but not by me! Instead, glass-fibre matting with filler, or glass-fibre filler, would probably suffice. I decided to give the glass-fibre matting a try and bought a small kit from Toolstation. I also heeded the advice Ash had given me about being liberal with the solvent during application.

The results weren’t too bad. It cured quite well and provided a stable surface onto which I could apply some filler to finish things off.

With many of the items cleaned up and ready for painting, the next step was to paint the engine tins, some minor loose components and the doors. However, I only painted the inside panels and door-shut areas of the doors. I plan to paint the outer door panels at the same time as the rest of the body.

Due to the heat, I had some issues with the primer being too thick or coming out too dry. Adding a little more thinners improved the spray pattern. Mindful of this, when it came to applying the colour I added more thinners to the mix to improve the atomisation of the paint.

The final result was OK — good enough for the engine tins and door shuts. I did have to flat back the glovebox door and polish it up, but it eventually looked OK, even though it was a slightly different shade of Clementine L20D orange to the previous batch.

Dash board mainly complete

Categories
bodywork brakes steering suspension

End of 2024 Update

It’s been a while but once the daily driver cars were sorted, I could recover from the financial strain they put me under and my focus could get on with fixing the Ford Corsair. I resolved the messed up paint job in the Beetle engine bay by using bright white aerosol primer & paint, however, the white wasn’t as glossy as the 2K paint due to being cellulose or acrylic but it will do for now. By November with the Corsair nearly ready for its MOT my attention went back on to the Beetle.

It began with a promo from BCS (Brake Calliper Specialists Ltd) in Nottingham with 25% off all brake calliper refurbishments. I had used them before 5 years ago for the Corsair and they come with a lifetime guarantee so I requested for a quote for refurbishment and painting in the Beetle L20D orange. What they came back with was rather expensive, so I had the quote adjusted for a standard black finish which saved me about £125.00! The total cost was £325.00 including the 25% discount which I thought was still quite expensive but assumed ‘business costs’ had gone up quite a lot since 2019.


For few days over the Christmas holiday I set about reassembling the front struts and noting extra parts required along the way like lower ball joint dust boots, brake lock tabs and strut rubber bump stops. I started with the lower ball joint and removed the split rubber boot and cleaned out the old dirty grease. I also used my Dremel with a low grit sand paper to get the ingrained dirt off the body and get it back to bare metal to then paint it with smooth white gloss Hammerite. The threads were re-tapped to clean them up and then the struts, stub axle & lower ball joint were loosely assembled together. All the minor components like bolts, dust caps and washers were all degreased and cleaned with the Dremel. On the stub axle, the threads for the brake calliper and back plate were all re-tapped after getting a bit contaminated from the powder coating process. They will be assembled properly once the new parts arrive.


The steering arm ball joints were cleaned up re-greased and new rubber dust boots fitted. Fitting the new dust boots was tricky to begin with but once they were secured in a vice it meant I could use both hands and small tipped flat bladed screw drivers to prise the (blue) metal spring clips to hold the new rubber boots in place. The joints were then assembled on to their tie-rod bars, but they too were a bit contaminated from the powder coating and would require a bit more work to screw in freely.

Categories
bodywork brakes

Brake Master Cylinder

After a year of waiting, I finally got around to sending my brake master cylinder for refurbishment in January/February 2023. As the pictures show, it was in a sorry state after sitting unused for over 27 years, causing it to dry out and deteriorate.

Initially, I considered buying a brand-new RHD master cylinder, but the cost of £200+ made it a less appealing option. Instead, I decided to opt for refurbishing my original one with a stainless steel inner sleeve, new seals, and black powder coating. The entire process was carried out by Past Parts, a reputable company based in Bury St Edmunds, UK, and took about two weeks to complete.

In the end, the cost of the refurbishment was less than £150, including all postage fees, allowing me to save a significant amount of money. This saving will be put towards purchasing new German brake circuit warning switches, which I hope to acquire soon.

Overall, I am pleased with the outcome of the refurbishment, and I’m glad that I opted for this option rather than buying a new part. It’s a great feeling to see my old brake master cylinder come back to life after so many years.

While I was in the workshop on a relatively mild day, I took the opportunity to do some body filler work. I started by sanding down the front right side quarter filler using 80 grit paper, before adding some more filler to the lower door ‘A’ posts to smooth out the lip from repair work done in 1997.

Last year, I spent some time researching how to work with automotive body filler and came across Bad Chad’s YouTube channel. His long but detailed video on filling and sanding techniques was particularly helpful, and I used his guidance to achieve decent results on the rear quarter panels. I also had some insightful conversations with John, a friend who restores classic cars and has worked on my Ford Corsair, as well as with Paul from South Coast Customs over the Christmas period. John offered to give me a hands-on tutorial on filling, sanding, and prepping for primer and paint in the spring, depending on his workload.

Recently, I discovered another YouTube channel by a British customizer named Paul Bacon. I was impressed by his straightforward, no-nonsense approach to bodywork and appreciated his creative style. His work, including the epic Automatron custom car, inspired me to continue learning and improving my skills. You can check out one of his videos below.

Note: This blog was written with the help of ChatGPT. The original blog post can be seen here.

Categories
bodywork brakes

Fettling

During October 2022, one of the other little jobs that had hung over me for the most part of 12 months was to finish off the brake lines for the rear. During the summer, I had found on eBay nearly new, flexible brake pipes for the front and rear and finally ordered from Amazon some male/female 10 mm brake pipe unions. I already had some 6 mm copper brake pipe left over from when I had done my Ford Corsair brake lines a few years ago. The pipes were made up and flexible hoses were fitted but only loosely tightened as they didn’t have any fluid in them. The master cylinder was still at this point needing to be sent away for refurbishment.

Having dabbled with filler and satisfied myself that there was a fair bit of work to be done I turned my attention to other parts of the car. If I was going to go the whole hog of a full body repaint then I needed to strip the body shell of more items. First was the headliner, which I kept for future refitting reference. Next was removal of door latches, interior light, dashboard instruments and switches. Removal of the dash instruments wasn’t too difficult, but putting it back together maybe something of a nightmare. I also removed the wiper mechanism along with the wirng loom, which was a birds nest of a mess as the plan is to renew it.

With the dash stripped out I could look at the body work side of things in more detail. One job that again had been hanging around in my head was the removal of the seal retaining strip that would have held the bonnet rubber. Paul had suggested that I go the Mexican Beetle method of the rubber that attaches to the bonnet and engine lid for a cleaner finish. So with a new spot weld chisel I set to breaking off the spot welds and had the retaining strips removed in a relatively short space of time. The remnants of the spot welds just needed to be ground flat and smoothed. I doubt the car (if/when finished) will see much of the rain when used, especially if the new seals (when fitted) aren’t very good.

The front valence had taken a bit of a battering when the body was being removed from the floor pan way back in June 2021. Paul had knocked out the worst of the dents and deformation before returning the body to me but I had a go with my planishing hammer and dolly to re-shape it some more. The result was an improvement and the first time that I had done such panel beating. The surface will be finished with filler.

One of the last jobs, prior to doing the Bedliner job (next post), was the very dusty task of cleaning up the rear luggage area from the remains of old insulation and sound deadening materials. I used a cupped wire brush and a knotted wire wheel on my angle grinder. It meant it was a clean area ready as a practice area for trying out primer and painting colour, later on. On the rear lower cross member with the large oval holes, these would accommodate the heater pipes from the engine. Captive nuts would need to be welded around these vent holes before any attempt at primer spraying would be done. I acquired from Paul a couple of vent pipes that had gone missing as replacements and to act as templates to sort his out.