Categories
bodywork brakes paint

Summer Jobs 2026

I had been busy on and off with various jobs on the Beetle. The first priority was to finish plumbing in the brake system now that the body was back on. I’ll say it now: fitting the pipework from the brake fluid reservoir to the master cylinder was, so far, probably the most frustrating and awkward job I have had to do on this little car.

From getting the bends in the pipes in the right places, fitting the correct amount of braided rubber hose, to eventually removing the master cylinder so I could push-seat the pipes properly, it was all a bit of a faff. In the end, I assembled around two-thirds of the system on the bench, including the master cylinder, and then made the final connections between the fluid reservoir and the remaining third of the pipework under the car at the bulkhead.

With all the pipework connected, and with some trepidation, I put in the brake fluid. Then some more, and then some more… until I noticed a leak at a joint on the frame head, which I duly tightened up.

I then noticed two large puddles of brake fluid at the rear.

When I first installed the brake lines back in September 2021, I hadn’t tightened them up. So, typically, now that the body was back on, the leaks were in awkward places above the torsion tube, at the ‘T’ joints in the pipes, as well as from both rear bleed nipples. After tussling with the awkward access to the brake-line fittings, I eventually got everything tightened up and the system stopped leaking. The rear brakes, however, still needed adjusting.

Hot weather arrived during May and the next job was to remove the engine tins ready for refurbishment. The only one I couldn’t remove was the panel behind the main crank pulley, as I didn’t have a 36mm socket.

Cleaning the engine tins and ‘doghouse’ fan shroud was a filthy job, covering both myself and much of the workshop in dust. Thankfully, I was wearing a face mask, so I didn’t get too much of it up my nose!

With the tins back to bare metal, I treated them with Jenolite, a rust-converter treatment in an aerosol.

With the hot weather continuing, I decided to turn my attention to the doors, as both needed a bit of attention due to rust appearing along their lower edges. Dismantling them was made much easier after watching a YouTube video by “Slades VW Beetle“. The process was quite straightforward, and with a bit of care it was easy enough to follow the steps in the video.

Stripping the doors back to bare metal was another hot and dirty job, once again plastering the workshop, and everything in it, with a layer of dust. I treated the exposed bare metal with Jenolite, including those awkward-to-reach areas.

There were a few previous rust repairs that I removed, which exposed a few more holes, but thankfully not too many. In fact, the doors were actually in pretty good order. They are clearly replacement doors from a previous restoration, judging by the evidence of their previous colour on the inside panels.

I went to see Paul (and Ash) during this period and, while the main purpose of the visit was to arrange a timeframe for the engine strip-down, I also took the opportunity to get some ideas on repairing the doors.

Welding would have been an option, but not by me! Instead, glass-fibre matting with filler, or glass-fibre filler, would probably suffice. I decided to give the glass-fibre matting a try and bought a small kit from Toolstation. I also heeded the advice Ash had given me about being liberal with the solvent during application.

The results weren’t too bad. It cured quite well and provided a stable surface onto which I could apply some filler to finish things off.

With many of the items cleaned up and ready for painting, the next step was to paint the engine tins, some minor loose components and the doors. However, I only painted the inside panels and door-shut areas of the doors. I plan to paint the outer door panels at the same time as the rest of the body.

Due to the heat, I had some issues with the primer being too thick or coming out too dry. Adding a little more thinners improved the spray pattern. Mindful of this, when it came to applying the colour I added more thinners to the mix to improve the atomisation of the paint.

The final result was OK — good enough for the engine tins and door shuts. I did have to flat back the glovebox door and polish it up, but it eventually looked OK, even though it was a slightly different shade of Clementine L20D orange to the previous batch.

Dash board mainly complete

Categories
bodywork paint painting steering suspension

Front Brakes and Suspension Refit

March 2026: With the body and floor pan finally reunited, I was keen to press on and get the brake lines finished and the front suspension components fitted. Before that though, I wanted to freshen up the front wheel arches so they matched the rears. I still had plenty of the white paint left over from doing the engine bay and rear arches last summer. As always, it took longer to set everything up and clean up afterwards than it did to actually get a decent coat on.

Installing the steering set-up fought me all the way. Initially, there wasn’t enough of the steering shaft protruding to fit the steering wheel, and when I unhitched the column from the universal coupling, there still wasn’t enough length to connect to the steering box. In the end, with the steering wheel fitted and a bit of persuasion from a soft mallet, I eased the column further into its housing until the splined shaft finally met the universal joint on the steering box.

With that small victory, I moved on to fitting the steering tie rods and damper while I still had plenty of room to work.

Fitting the rebuilt front struts was relatively straightforward, although I did have to undo the anti-roll bar mountings to get the lower ball joint seated properly into the track control arms. Once in place, I connected the track rod ends to the steering arms on the struts.

Then came the first “ah” moment — with the wheels on, they were clearly pointing outwards. Not ideal. It turned out the track rod ends hadn’t been wound far enough into the rods, thanks to threads contaminated with sand and grit from the earlier media blasting and powder coating.

1302S Front right side steering components
Front right side steering components, note the tie rod end not wound in very much

So, out it all came again. This time, carefully manoeuvring everything around the now-fitted struts. With the track rods clamped firmly in the vice on the workbench, I worked the ends in and out, cleaning the threads millimetre by millimetre. It took a while, but eventually I had enough adjustment to make a future alignment possible.

Back under the car on the mechanic’s creeper, I went through the now-familiar routine of refitting everything. Thankfully, it wasn’t too arduous this time. Once reconnected, I stepped back — and the wheels were finally pointing forwards.

1302S with front suspension and steering fitted
1302S with front suspension and steering fitted

With that sorted, I turned back to the brakes. I finished fitting the copper lines along the frame head and up to the flexi pipe connections, making the most of the access underneath the car while I still could. Fitting the flexi pipes to the front struts was straightforward, and shaping the copper lines neatly around the lower struts to those freshly rebuilt calipers was a particularly satisfying job.

frame head brake line
frame head brake line

I also dug out the brake fluid reservoir and its associated pipework from storage, only to find the pipes were in poor condition — and one was missing altogether. New ones will need to be made up from 8mm piping.

With the wheels back on, it marked a bit of a milestone — the first time since June 2021 that the car was back on all fours.

Categories
bodywork brakes steering suspension

End of 2024 Update

It’s been a while but once the daily driver cars were sorted, I could recover from the financial strain they put me under and my focus could get on with fixing the Ford Corsair. I resolved the messed up paint job in the Beetle engine bay by using bright white aerosol primer & paint, however, the white wasn’t as glossy as the 2K paint due to being cellulose or acrylic but it will do for now. By November with the Corsair nearly ready for its MOT my attention went back on to the Beetle.

It began with a promo from BCS (Brake Calliper Specialists Ltd) in Nottingham with 25% off all brake calliper refurbishments. I had used them before 5 years ago for the Corsair and they come with a lifetime guarantee so I requested for a quote for refurbishment and painting in the Beetle L20D orange. What they came back with was rather expensive, so I had the quote adjusted for a standard black finish which saved me about £125.00! The total cost was £325.00 including the 25% discount which I thought was still quite expensive but assumed ‘business costs’ had gone up quite a lot since 2019.


For few days over the Christmas holiday I set about reassembling the front struts and noting extra parts required along the way like lower ball joint dust boots, brake lock tabs and strut rubber bump stops. I started with the lower ball joint and removed the split rubber boot and cleaned out the old dirty grease. I also used my Dremel with a low grit sand paper to get the ingrained dirt off the body and get it back to bare metal to then paint it with smooth white gloss Hammerite. The threads were re-tapped to clean them up and then the struts, stub axle & lower ball joint were loosely assembled together. All the minor components like bolts, dust caps and washers were all degreased and cleaned with the Dremel. On the stub axle, the threads for the brake calliper and back plate were all re-tapped after getting a bit contaminated from the powder coating process. They will be assembled properly once the new parts arrive.


The steering arm ball joints were cleaned up re-greased and new rubber dust boots fitted. Fitting the new dust boots was tricky to begin with but once they were secured in a vice it meant I could use both hands and small tipped flat bladed screw drivers to prise the (blue) metal spring clips to hold the new rubber boots in place. The joints were then assembled on to their tie-rod bars, but they too were a bit contaminated from the powder coating and would require a bit more work to screw in freely.