Categories
bodywork brakes paint

Summer Jobs 2026

I had been busy on and off with various jobs on the Beetle. The first priority was to finish plumbing in the brake system now that the body was back on. I’ll say it now: fitting the pipework from the brake fluid reservoir to the master cylinder was, so far, probably the most frustrating and awkward job I have had to do on this little car.

From getting the bends in the pipes in the right places, fitting the correct amount of braided rubber hose, to eventually removing the master cylinder so I could push-seat the pipes properly, it was all a bit of a faff. In the end, I assembled around two-thirds of the system on the bench, including the master cylinder, and then made the final connections between the fluid reservoir and the remaining third of the pipework under the car at the bulkhead.

With all the pipework connected, and with some trepidation, I put in the brake fluid. Then some more, and then some more… until I noticed a leak at a joint on the frame head, which I duly tightened up.

I then noticed two large puddles of brake fluid at the rear.

When I first installed the brake lines back in September 2021, I hadn’t tightened them up. So, typically, now that the body was back on, the leaks were in awkward places above the torsion tube, at the ‘T’ joints in the pipes, as well as from both rear bleed nipples. After tussling with the awkward access to the brake-line fittings, I eventually got everything tightened up and the system stopped leaking. The rear brakes, however, still needed adjusting.

Hot weather arrived during May and the next job was to remove the engine tins ready for refurbishment. The only one I couldn’t remove was the panel behind the main crank pulley, as I didn’t have a 36mm socket.

Cleaning the engine tins and ‘doghouse’ fan shroud was a filthy job, covering both myself and much of the workshop in dust. Thankfully, I was wearing a face mask, so I didn’t get too much of it up my nose!

With the tins back to bare metal, I treated them with Jenolite, a rust-converter treatment in an aerosol.

With the hot weather continuing, I decided to turn my attention to the doors, as both needed a bit of attention due to rust appearing along their lower edges. Dismantling them was made much easier after watching a YouTube video by “Slades VW Beetle“. The process was quite straightforward, and with a bit of care it was easy enough to follow the steps in the video.

Stripping the doors back to bare metal was another hot and dirty job, once again plastering the workshop, and everything in it, with a layer of dust. I treated the exposed bare metal with Jenolite, including those awkward-to-reach areas.

There were a few previous rust repairs that I removed, which exposed a few more holes, but thankfully not too many. In fact, the doors were actually in pretty good order. They are clearly replacement doors from a previous restoration, judging by the evidence of their previous colour on the inside panels.

I went to see Paul (and Ash) during this period and, while the main purpose of the visit was to arrange a timeframe for the engine strip-down, I also took the opportunity to get some ideas on repairing the doors.

Welding would have been an option, but not by me! Instead, glass-fibre matting with filler, or glass-fibre filler, would probably suffice. I decided to give the glass-fibre matting a try and bought a small kit from Toolstation. I also heeded the advice Ash had given me about being liberal with the solvent during application.

The results weren’t too bad. It cured quite well and provided a stable surface onto which I could apply some filler to finish things off.

With many of the items cleaned up and ready for painting, the next step was to paint the engine tins, some minor loose components and the doors. However, I only painted the inside panels and door-shut areas of the doors. I plan to paint the outer door panels at the same time as the rest of the body.

Due to the heat, I had some issues with the primer being too thick or coming out too dry. Adding a little more thinners improved the spray pattern. Mindful of this, when it came to applying the colour I added more thinners to the mix to improve the atomisation of the paint.

The final result was OK — good enough for the engine tins and door shuts. I did have to flat back the glovebox door and polish it up, but it eventually looked OK, even though it was a slightly different shade of Clementine L20D orange to the previous batch.

Dash board mainly complete

Categories
bodywork paint painting

A little more primer

By the end of May I had plopped on some more filler to smooth out a few bumps and high spots, mainly on the rear valence and engine bay aperture. I also added some filler to sort out the minor corrosion on the rain gutter on the right side (UK drivers side) above the door. I spent a few on/off days of May into June, rubbing back the filler on the rain gutter repair, rear valence and other small areas on rear portions of the body. I was beginning to think the body was now in the final stages of near completion, but I still have plenty of filler if needed. Around this time I visited Paul at South Coast Customs and he had a 1966 Beetle that he was restoring but was taking it back to bare metal first. The filler on that car was 5-10mm thick on the lower rear quarter panels and hid a multitude of poorly executed repairs, something I wanted to avoid this car in having too much filler.

At the end of this stage I was considering the options of installing a third brake eye, behind the cooling grills above the engine compartment. There was a mixture views on the Volkszone forum, especially cutting into the metal work beneath the rear window to insert a removable plate with an after market LED brake light fitted. With the 1302S being a relatively scarce Beetle these days, I had begun second thoughts on making a cut out under the rear window to insert the 3rd brake eye and started to consider a self adhesive LED light strip instead.

My other question to the forum was whether I should grind off or keep the tar board hooks on the engine bay firewall – I didn’t need much convincing… I decided to grind off the tabs which in doing so was sending an unmanageable shower of sparks that were getting everywhere all over me. I resorted to knocking them off with my spot weld chisel and then grind back with a flap disc, far less sparks flying all over the place. The only problem with knocking off the spot welds was that it created two more holes in the fire wall that I will have to fill or cover up.

I laid a (fourth) coat of primer on the rubbed down areas and the engine firewall looked a lot neater with the tar board tags having been removed. The rear valence was repainted and other smaller parts like the fuel filler flap and engine lid hinge mounts were painted in primer as well.

Categories
bodywork brakes

Brake Master Cylinder

After a year of waiting, I finally got around to sending my brake master cylinder for refurbishment in January/February 2023. As the pictures show, it was in a sorry state after sitting unused for over 27 years, causing it to dry out and deteriorate.

Initially, I considered buying a brand-new RHD master cylinder, but the cost of £200+ made it a less appealing option. Instead, I decided to opt for refurbishing my original one with a stainless steel inner sleeve, new seals, and black powder coating. The entire process was carried out by Past Parts, a reputable company based in Bury St Edmunds, UK, and took about two weeks to complete.

In the end, the cost of the refurbishment was less than £150, including all postage fees, allowing me to save a significant amount of money. This saving will be put towards purchasing new German brake circuit warning switches, which I hope to acquire soon.

Overall, I am pleased with the outcome of the refurbishment, and I’m glad that I opted for this option rather than buying a new part. It’s a great feeling to see my old brake master cylinder come back to life after so many years.

While I was in the workshop on a relatively mild day, I took the opportunity to do some body filler work. I started by sanding down the front right side quarter filler using 80 grit paper, before adding some more filler to the lower door ‘A’ posts to smooth out the lip from repair work done in 1997.

Last year, I spent some time researching how to work with automotive body filler and came across Bad Chad’s YouTube channel. His long but detailed video on filling and sanding techniques was particularly helpful, and I used his guidance to achieve decent results on the rear quarter panels. I also had some insightful conversations with John, a friend who restores classic cars and has worked on my Ford Corsair, as well as with Paul from South Coast Customs over the Christmas period. John offered to give me a hands-on tutorial on filling, sanding, and prepping for primer and paint in the spring, depending on his workload.

Recently, I discovered another YouTube channel by a British customizer named Paul Bacon. I was impressed by his straightforward, no-nonsense approach to bodywork and appreciated his creative style. His work, including the epic Automatron custom car, inspired me to continue learning and improving my skills. You can check out one of his videos below.

Note: This blog was written with the help of ChatGPT. The original blog post can be seen here.

Categories
bodywork brakes

Fettling

During October 2022, one of the other little jobs that had hung over me for the most part of 12 months was to finish off the brake lines for the rear. During the summer, I had found on eBay nearly new, flexible brake pipes for the front and rear and finally ordered from Amazon some male/female 10 mm brake pipe unions. I already had some 6 mm copper brake pipe left over from when I had done my Ford Corsair brake lines a few years ago. The pipes were made up and flexible hoses were fitted but only loosely tightened as they didn’t have any fluid in them. The master cylinder was still at this point needing to be sent away for refurbishment.

Having dabbled with filler and satisfied myself that there was a fair bit of work to be done I turned my attention to other parts of the car. If I was going to go the whole hog of a full body repaint then I needed to strip the body shell of more items. First was the headliner, which I kept for future refitting reference. Next was removal of door latches, interior light, dashboard instruments and switches. Removal of the dash instruments wasn’t too difficult, but putting it back together maybe something of a nightmare. I also removed the wiper mechanism along with the wirng loom, which was a birds nest of a mess as the plan is to renew it.

With the dash stripped out I could look at the body work side of things in more detail. One job that again had been hanging around in my head was the removal of the seal retaining strip that would have held the bonnet rubber. Paul had suggested that I go the Mexican Beetle method of the rubber that attaches to the bonnet and engine lid for a cleaner finish. So with a new spot weld chisel I set to breaking off the spot welds and had the retaining strips removed in a relatively short space of time. The remnants of the spot welds just needed to be ground flat and smoothed. I doubt the car (if/when finished) will see much of the rain when used, especially if the new seals (when fitted) aren’t very good.

The front valence had taken a bit of a battering when the body was being removed from the floor pan way back in June 2021. Paul had knocked out the worst of the dents and deformation before returning the body to me but I had a go with my planishing hammer and dolly to re-shape it some more. The result was an improvement and the first time that I had done such panel beating. The surface will be finished with filler.

One of the last jobs, prior to doing the Bedliner job (next post), was the very dusty task of cleaning up the rear luggage area from the remains of old insulation and sound deadening materials. I used a cupped wire brush and a knotted wire wheel on my angle grinder. It meant it was a clean area ready as a practice area for trying out primer and painting colour, later on. On the rear lower cross member with the large oval holes, these would accommodate the heater pipes from the engine. Captive nuts would need to be welded around these vent holes before any attempt at primer spraying would be done. I acquired from Paul a couple of vent pipes that had gone missing as replacements and to act as templates to sort his out.

Categories
bodywork

… some time later

Talk about taking my time. My main excuse for the long break was that from March to August 2022 we had goose eggs being incubated and then the single success of a hatched gosling was growing up in the workshop that housed the beetle. The gosling (Ashley) took up a fair amount of space so working on the beetle just couldn’t happen. At least, with some assistance, I had got the body shell up on to the trestles which I had made at the end of November 2021, therefore I could roll and store the floor pan underneath.

Way back in March 2022, I bought a 3 litre tin of 3M filler with hardener, 5 litres (with hardener) of high build primer, 5 litres of thinners and 3 Cobra Bedliner systems (anti stone chip) to use with a Schultz spray gun. Roll on September 2022 and I had the space to work on the body shell and my first job was to try out the filler on the rear quarters.

The body filling was done over several days with the first layer being rubbed back initially with an orbital sander and 80 grit paper to expose the low points. A second layer was applied and rubbed back by hand to reveal the low spots again and thus a third layer was applied and though an improvement there were still low spots after a combination of orbital and hand sanding. Having seen something on YouTube, I bought some better filler spreaders as the plastic applicator (vinyl applicator) I had been using was too stiff and not giving any flex to follow the body shape.

After the third filling and rubbing down attempt I decided to stop and seek some assurance by speaking to Paul before I went any further. I had by then got a reasonable idea for filling and trying the techniques of rubbing down with different grades of paper – I just needed to take my time therefore turned my attention to stripping the car down to just a shell.

Categories
bodywork welding

The Body Shell

November 2021: With the semi-rolling floor pan returned home, Paul had the body shell to work on. By the time I went back to his workshop to help out, a couple of weeks later, he had already replaced the rear bumper bracket mount, repair sections so as to get it up on to a rotisserie. He had also formulated the rudimentary set up for the removable rear valence. The removable rear valence would greatly assist in the installation and any future removal of the engine.

With the bumper mounts repaired, attention was to look at the quarter panel repairs previously done in 1997. It was apparent that the welding on both sides were of varying quality (possible by two different people) and the repair panels overlapped the old metal by a large amount. The right side (UK driver side) was the worst with deformation and warpage and Paul felt it was best to cut the whole rear quarter out and replace it with a new panel. The left side wasn’t too bad but Paul trimmed the excessive overlap on the 1997 repair and welded it in further down the existing original rear quarter meaning less filler would be needed to cover the repair.

With some strength back in the body, Paul set to work on the right inner rear wheel arch repair with the body mounting bracket. A large repair section had been purchased by me earlier in the year and judging by the pictures it seemed this was a relatively straight forward job.

A not so simple job, was the replacement and widening of the front firewall. The (cheaper Klokkerholm) panel I had supplied meant Paul spent quite a bit of time cutting and fabricating this up to be right, along with a front left strut repair. As for me, I was grinding down the welds on the earlier jobs done by Paul as well as cleaning up the underside of the rear body and painting all the exposed metal in red oxide primer.

Some more images to show the work that was done. The pile of removed metal was quite substantial and there were layers upon layers of repair patches – that should save a bit of weight.

By the end of November, the 1302 body shell was returned home and put alongside it’s floor pan.

Categories
floor pan

The Floor Pan

July 2021: A few weeks after separating the body from the floor I went over to help Paul strip the floor pan down to its bare chassis spine. To start, we had to remove the previously replaced floors by cutting as close to the main central tunnel as we could, but ensuring not to cut into the tunnel structure its self as this was where the floors would be spot (or plug) welded to. Using a trusty cold chisel, Paul then hammered out all the spot welds on the left side (passenger side RHD), as this was still the original factory floor because in 1997 we only had a ‘half’ floor fitted. On the right side the floor that was fitted in 1997 had been seam welded along its length to the chassis central spine. Initial thoughts were that this was going to be a problem but upon closer inspection the seam weld had been done on top of the remains of the old original floor. Thankfully, this allowed Paul to use his chisel and knock out the factory spot welds on the original floor and thus taking the newer welded floor left overs with it.

The central tunnel was covered in a tar based sound deadening board, so chipping and cleaning off this material was my job and something I could actually do. It didn’t take too long and by early afternoon the chassis was stripped bare. All that was needed was for the frame head to be replaced, but Paul would have to make up a jig to ensure the new frame head and the underside part of the Napoleon’s Hat, a section to be grafted in, would all align.

A few days later I got a message with pictures from Paul to say he spent a whole day on the chassis and got the new frame head on, new floors fitted, and also the Napoleon’s Hat section of the floor grafted in. He had a spare 1302 shell in his yard that he used to offer the floor up to ensure everything aligned as it should.

The following week I went over again to Pauls to see the results of his welding and look over the thorough job he had done. Later, we set to stripping down the IRS arms, spring plates, rear brakes, front TCAs and other small parts in readiness to be sent away for media blasting and powder coating.

Categories
Uncategorized

Restoration – 3rd Attempt

June 2021: It was a warm sunny Saturday when Paul from South Coast Customs & Classics arrived to transport the 1302S Beetle back to his workshop. The plan that day was to separate the body from the floor pan as well as strip down the car some more so the welding on the body and replacement of the frame head could commence.

It turned out to be a lot more difficult than expected with the body being welded to the floor pan in a few locations. Each corner on the rear edge of the floors, each side of bulkhead and on each side of the frame head near the body mounting points. Paul had to cold chisel, angle grind and lever the body and floor apart to break the welds off, though some crumbled due to corrosion. After a fair amount of sweat and effort by Paul the body was ready to be lifted off, quite possibly for the first time in it’s life. Looking at the amount of work Paul had put in to separate the body and floor I was glad he was on board to deal with this, I couldn’t have ever managed that.

With the floor pan now exposed it was clear to see the poor state it was in, even the new floors which were put in 1997 were effectively scrap due to being welded to the body. The frame head had already been identified to be replaced and the “napoleon’s hat” floor pan bulkhead was in a poor state.

I’m not sure if Paul was being kind, but he said it wasn’t the worst beetle he had worked on, which kind of reassured me that this wasn’t going to be too difficult for him to tackle.

Categories
Uncategorized

Professional Help

A year later, Autumn 1997, we had the finances to take the Beetle to seek a professional and were directed to a chap known as Mike the Welder, who was taking over a former VW specialist garage on the Wimborne Road in Bournemouth. Buoyed by his no problem approach and promising to keep his current rates for the project he took it on as his first car at the new premises, now renamed as Small Car Projects, in October 1997. Mike and a member of his team worked on the Beetle on and off through to the November of 1997. New front inner arch panels left and right, rear lower quarter repair panels left and right, new right hand floor, new half left hand floor, new lower A post panel repairs left and right and rear floor repairs right side were done.

Mike kept the car over the winter as he identified that it would be easier to replace the spare wheel well and front valence rather than repair the accident damage. We needed to save up a bit more cash in that time. By March 1998 the front end had been replaced with new panels and the beetle was delivered back to our lock up. Mike had assured us all was good with the body and that it could be removed from the floor if needed in the future. We were happy and it looked like a good job had been done.

Other life events took over from mid 1998 and the Beetle lay dormant in the garage until it had to be moved in the Summer of 2000.