Categories
engine painting

Engine Strip Down

August 2026: I spent part of a Saturday with Paul (South Coast Customs & Classics) stripping down the Beetle’s engine block. I had removed as much as I dared, including the carburettor, fuel intakes, engine tins, fan shroud, dynamo, heat exchangers and exhaust system. I couldn’t separate the fan assembly from the dynamo as I didn’t have a 36mm socket, so I had to rely on Paul for that.

With the engine in the boot of my Passat, Paul’s engine stand was at the perfect height to attach to the engine without any major lifting. You could almost have wondered if VW had thought of this all along when they designed the rear hatch boot access!

Initial inspection revealed the crankshaft end-float was about 2mm (normal is anything less than 0.5mm), and this became particularly evident after splitting the case, with noticeable movement around the main bearing. The saving grace was that there was enough metal left to allow the block to be re-machined for new main bearings.

The crankshaft seemed to be in good condition, with no hot spots or heat tarnishing, and the con rods were OK, with minimal movement at the gudgeon pin end. The piston and barrel bores were clean, with no scoring, and appeared reusable, as did the pistons if fitted with new rings.

The camshaft, and especially the lifters, showed signs of wear. What I hadn’t expected to find was that both cylinder heads had cracks between the valves. I was advised not to reuse them, although, according to the Forums, there are two camps when it comes to the argument over reusing cracked cylinder heads.

So, a rethink was on the cards for the engine build, along with some new costs to consider. Prior to all this work, I had used Chat-GPT to spec up an engine rebuild and associated costs, but now I had to factor in the additional expense of new cylinder heads.

I opted for the Heritage deal from the VW specialist supplier, which included two new cylinder heads along with new 1641 barrels and pistons, seals and all the gaskets required for the bottom-end rebuild. I also went for new con rods, as they came with the piston (gudgeon pin) bushes already fitted.

A 110 Engle cam kit was ordered too, as it came with all the gaskets and lifters required for a complete job. Paul would send the disassembled block away for machining, which would include matching new bearings as part of the process to resolve the huge amount of end-float.

The parts not being sent away for machining were put into a box so I could take them home and clean them up ready for when we put the engine back together. Everything got a good degreasing scrub with Gunk and was then rinsed with petrol to remove years of old grime.

The crankshaft pulley wheel, rocker covers, lower pulley tinware, dynamo fan-shroud mounting plates and many small parts were further cleaned to remove old paint, corrosion and other ingrained dirt using various angle-grinder attachments. The flywheel and clutch pressure plate were also given the light abrasive angle-grinder treatment and came up well, so hopefully they will be usable.

On my Chat-GPT engine build sheet, I had factored in Pertronix electronic ignition and twin Weber 34 ICTs. However, keeping my options open, I decided to clean, lubricate and rejuvenate the distributor with new parts, and give the Solex 34 PICT-3 carburettor a thorough clean and rebuild. This means I have the option of keeping things stock for now.

All the parts were at least clean, looking nice and ready to go back onto the engine.

Categories
bodywork paint painting steering suspension

Front Brakes and Suspension Refit

March 2026: With the body and floor pan finally reunited, I was keen to press on and get the brake lines finished and the front suspension components fitted. Before that though, I wanted to freshen up the front wheel arches so they matched the rears. I still had plenty of the white paint left over from doing the engine bay and rear arches last summer. As always, it took longer to set everything up and clean up afterwards than it did to actually get a decent coat on.

Installing the steering set-up fought me all the way. Initially, there wasn’t enough of the steering shaft protruding to fit the steering wheel, and when I unhitched the column from the universal coupling, there still wasn’t enough length to connect to the steering box. In the end, with the steering wheel fitted and a bit of persuasion from a soft mallet, I eased the column further into its housing until the splined shaft finally met the universal joint on the steering box.

With that small victory, I moved on to fitting the steering tie rods and damper while I still had plenty of room to work.

Fitting the rebuilt front struts was relatively straightforward, although I did have to undo the anti-roll bar mountings to get the lower ball joint seated properly into the track control arms. Once in place, I connected the track rod ends to the steering arms on the struts.

Then came the first “ah” moment — with the wheels on, they were clearly pointing outwards. Not ideal. It turned out the track rod ends hadn’t been wound far enough into the rods, thanks to threads contaminated with sand and grit from the earlier media blasting and powder coating.

1302S Front right side steering components
Front right side steering components, note the tie rod end not wound in very much

So, out it all came again. This time, carefully manoeuvring everything around the now-fitted struts. With the track rods clamped firmly in the vice on the workbench, I worked the ends in and out, cleaning the threads millimetre by millimetre. It took a while, but eventually I had enough adjustment to make a future alignment possible.

Back under the car on the mechanic’s creeper, I went through the now-familiar routine of refitting everything. Thankfully, it wasn’t too arduous this time. Once reconnected, I stepped back — and the wheels were finally pointing forwards.

1302S with front suspension and steering fitted
1302S with front suspension and steering fitted

With that sorted, I turned back to the brakes. I finished fitting the copper lines along the frame head and up to the flexi pipe connections, making the most of the access underneath the car while I still could. Fitting the flexi pipes to the front struts was straightforward, and shaping the copper lines neatly around the lower struts to those freshly rebuilt calipers was a particularly satisfying job.

frame head brake line
frame head brake line

I also dug out the brake fluid reservoir and its associated pipework from storage, only to find the pipes were in poor condition — and one was missing altogether. New ones will need to be made up from 8mm piping.

With the wheels back on, it marked a bit of a milestone — the first time since June 2021 that the car was back on all fours.

Categories
bodywork paint painting seals

Engine Bay Paint and Rubber

At the end of summer the weather was still warm and dry, so I took the opportunity to respray the engine bay in bright white, as before, however this time with successful results. With some fiddling I worked out how to get my spray gun to a correct working pressure and I took extra care of getting my paint mixture right. I took my time spraying three thin, wet coats with 4-5 minute pauses between each coat allowing for it to flash off. I took the opportunity to spray the rear wheel arches to clean them up as well and the result was a fresh glossy finish and finally to my satisfaction.

Another milestone achieved was fitting the engine bay seals that I got from Just Kampers. Fitting of the firewall seal was relatively straight forward, not too much prying or effort required and was done in a bout 20 minutes. The other engine bay rubber was more tricky, though made easier because of the removable rear valance and I could do it in three stages. Rubber gloves, the type used for mechanical work with a pair of large pliers were needed for a good firm grip and vaseline to ease and slide the rubber into the channel. It took about 45 mins to complete.

Categories
bodywork paint painting

Painting – the fifth time

On the Wedenesday I went to visit Paul at South Coast Customs & Classics, however, it turned out I could do him a favour. As I was driving to Charlton Marshal, just outside Blandford, I saw Paul in a bus-stop layby with a very smart blue Beetle with the engine lid open. Luckily there was a bus-stop layby opposite, so I pulled over to see what was going on. The blue Beetle had an ignition failure while on the way to the MOT station and was only 100 metres short of getting there but the garage didn’t want to MOT the car if it couldn’t be driven in. As it happened, I had a tow rope in the boot of my Corsair and offered to get Paul and the Beetle back to his workshop. Once back to the workshop and the Beetle pushed in to the work bay, I got to meet Ash his new work colleague, for the past couple of years.

Categories
bodywork paint painting

Painting the 4th time

I couldn’t help but to mock up with the wings and the removable rear valance, it almost looked like it was nearly there… finished! It did confirm my thoughts that I would need better condition rear wings, but the fronts were OK.

The last paint attempt wasn’t too bad – in most parts I could live with it, but as I was preparing to do the bonnet shuts, front scuttle, front quarter panels and lower parts of the front valence I felt it worth while re-doing the dashboard again as well as digging out the rear valence to paint that too. It turned out to be decision I would regret. Again, various factors at play here from a bad spray gun set up to paint being too ‘dry’ or having too much faith in the fast hardner. Whatever, the paint came out in a spatter (again) and the finish was as expected textured, lumpy orange peel.

I must be glutton for punishment and mockery, its terrible.
This is a portion of the rear valence, takes a brave person to admit to doing this.

So it seems I have a pattern of work, paint on a Sunday, only to rub it all back on the Monday. Well, not the rear valance, thats my sample to show people how bad I am at car spray painting and also gather some advice from folk who know how to paint cars. My next step is to get some advice, salvage the existing paint or buy some fresh paint with standard hardner.

Categories
bodywork paint painting

Body Work and Paint

Painting back in May (2025) with colour was another failure.
As I mentioned in my last blog, it was actually worse than my first attempt. A severely clogged spray gun, full of old paint, combined with blocked vents on the paint cup, only added to the list of faults with my cheap 1.5-nozzle gun. The replacement 1.4 Fast Mover FMT 3006/1.4 hadn’t fared much better either, thanks to a poor clean after the earlier primer disaster.

VW 1302S Beetle body in pre-paint prep stage
VW 1302S Beetle body in pre-paint prep stage
Categories
paint painting

Painting 2K

After watching a few YouTube videos, I gave spray painting a shot in the engine bay around the end of July 2023. I chose bright white (RAL 9010) and used the hardener/activator that came with the primer. I was careful not to use too much, as I thought the primer and hardener were best kept to work together in their specific proportions.

My first try didn’t go so well. I put on too much paint at once and used too high of an air pressure. This resulted in paint running, dripping, and forming pools in the engine bay. I was able to fix it by sanding down the runs, getting rid of the drips, and smoothing out the pooled paint. This got things ready for my second attempt. I also had to apply some primer again on the areas where I had sanded down to bare metal.

Categories
bodywork paint painting

A little more primer

By the end of May I had plopped on some more filler to smooth out a few bumps and high spots, mainly on the rear valence and engine bay aperture. I also added some filler to sort out the minor corrosion on the rain gutter on the right side (UK drivers side) above the door. I spent a few on/off days of May into June, rubbing back the filler on the rain gutter repair, rear valence and other small areas on rear portions of the body. I was beginning to think the body was now in the final stages of near completion, but I still have plenty of filler if needed. Around this time I visited Paul at South Coast Customs and he had a 1966 Beetle that he was restoring but was taking it back to bare metal first. The filler on that car was 5-10mm thick on the lower rear quarter panels and hid a multitude of poorly executed repairs, something I wanted to avoid this car in having too much filler.

At the end of this stage I was considering the options of installing a third brake eye, behind the cooling grills above the engine compartment. There was a mixture views on the Volkszone forum, especially cutting into the metal work beneath the rear window to insert a removable plate with an after market LED brake light fitted. With the 1302S being a relatively scarce Beetle these days, I had begun second thoughts on making a cut out under the rear window to insert the 3rd brake eye and started to consider a self adhesive LED light strip instead.

My other question to the forum was whether I should grind off or keep the tar board hooks on the engine bay firewall – I didn’t need much convincing… I decided to grind off the tabs which in doing so was sending an unmanageable shower of sparks that were getting everywhere all over me. I resorted to knocking them off with my spot weld chisel and then grind back with a flap disc, far less sparks flying all over the place. The only problem with knocking off the spot welds was that it created two more holes in the fire wall that I will have to fill or cover up.

I laid a (fourth) coat of primer on the rubbed down areas and the engine firewall looked a lot neater with the tar board tags having been removed. The rear valence was repainted and other smaller parts like the fuel filler flap and engine lid hinge mounts were painted in primer as well.

Categories
paint painting

Floor Pan Bedliner Applied

As it was a good day for weather last Sunday (7th May) I got to roll the floor pan out and, with some help, turn it on it’s side in readiness to spray on the Bedliner for Color. It was the last of the 3 bottle batch I bought last year. It was something I had been wanting to do for a while. The main reason for the Bedliner/Shultz is that powder coating is nice but it chips easily, as I found out again when I caught the gearbox on the rear horns when I removed it to aid the turning of the floor pan on to its side. Also, if applied thickly it is supposed to help with the sound deadening, guess I’ll take those people’s word for it.

I only did the floor underside and the frame head as, in my (uneducated) opinion, they were most likely to take the brunt of the road rash, when this car finally makes on the road. Note, the wooden beam was just a precaution, the whole thing on its side was self supporting with out it. At the front, the track control arm end is through the centre hole of the wheel (wrapped in a cloth) and the anti roll bar is resting on a wooden block.

So this is what I used (above), as before on the beetle body shell inner wings, underside of the engine/gearbox cover and at the front underside. I also got to revisit missed areas of the body shell when I thought I made a good coverage of the floor pan/frame head. Hopefully that will be good enough to withstand various road conditions.

While the compressor and spray stuff was all out and the floor pan was drying I decided to re-apply more primer after the last primer session in April was rubbed down after more filler had been applied and rubbed back again. The end result is much better, it just needs a light rub back and then I will leave it for now to decide if more touch up filler is needed. There is a rust repair to do on the drip rail, just above the drivers door and most of the metal is there, so it will be a filler job.

I am very tempted to get the colour (Clementine L20D) done on the inside… However, I overspent a bit this month on spares, so it will have to wait until next month. The floor pan was dusted down, cleaned up, then covered in dust sheets and rolled back under the 1302 body shell.