Categories
bodywork floor pan seals

Body to Floor Pan

February 2026: The day finally arrived for the body to be put back onto the floor pan. Paul and his assistant, Ash, came over on Saturday afternoon, and I had prepped the work area as much as I could think of beforehand.

VW Beetle 1302S body on tressels
The body on tressels prior to fitting onto the floor pan.

Paul got straight to it, quickly cutting some notches in the rear crossmember rubber seal. We then used a strong carpet spray adhesive to stick the rubber seals to the floor pan.

The floor pan was wheeled back into place under the body, which had been supported on trestles for the last four years. While Paul and Ash lifted the body, I removed the trestles and they lowered it onto the floor pan in virtually one manoeuvre. After a couple of adjustments, all the heater channel bolts went in.

The rear crossmember body holes needed to be enlarged slightly for the bolts and washers to be installed properly. With some persuasion, the front crossmember bolts on the left side (RHD passenger side) went in. Paul then identified a problem on the right-hand side of the front crossmember, where the floor pan bolt holes (x2) were about 5mm off-centre. He said he would need to come back with his die grinder to enlarge the holes to access the captive nuts properly.

On Sunday, I managed to fit the front frame head bolts to secure the body on both the left and right sides. With a bit of leverage and some brute force, I fitted the left rear mounting bolt. The right side took more time, requiring the Dremel and a grinding tip to enlarge the mounting bracket hole.

Paul came by again the following Saturday to use his die grinder to rework the Napoleon hat front crossmember mounting bolt holes on the right side. As brutal as it sounded, Paul kept the grinding to a minimum within the bolt hole area. It looked a bit rough, but it would be covered by the large washers and bolts anyway.

I then had to reinsert the rubber floor pan seal, which was tricky. I had to lever the body up as much as I could—no more than about 3–4 mm—and carefully poke the seal back into place. Once I was satisfied the rubber was seated properly and the bolts would go back in without issue, I sprayed primer on the exposed metal before reassembly.

At last, the body was fully secured to the floor pan with all the bolts in place.

Categories
bodywork gearbox mechanics

Front Valence & Gearbox returns

The front valence had taken something of a beating way back in June 2021 when the body was removed from the floorpan. Now seemed the right time to try and fix it.

First a hammer and dolly was used to sort out the ripples, high spots and dents. A plop of filler, sanded, some primer, smoothed and then a bit more filler, sanded and re-primered. I later applied some colour, which showed up some defects in my filler application but as I will do the paint again, it will serve as a ‘guide’ coat for now.

The gearbox came back from John Walklett Transmissions at the end of May. Fitting wasn’t as straightforward as I thought it would be and aligning the rubber gearbox mounts with the gearbox cradle was a struggle but I got there in the end. All associated components were re-attached and another major step forward made.

Lets have a look how it was 4 years ago, compared to now…

And here is where I got to with the 2nd attempt at applying colour. In fact the finish was worse than my first go, but with out the paint runs and sags. It came out the spray gun as a spatter, probably due to not enough air pressure to atomise the paint more and so the finish was very ‘textured’ much like orange peel. I used rattle can aerosol for around the engine lid mountings and rear air grill under the rear window. The finish came out as a satin finish, much like the white I did inthe engine bay.

Categories
paint painting

Floor Pan Bedliner Applied

As it was a good day for weather last Sunday (7th May) I got to roll the floor pan out and, with some help, turn it on it’s side in readiness to spray on the Bedliner for Color. It was the last of the 3 bottle batch I bought last year. It was something I had been wanting to do for a while. The main reason for the Bedliner/Shultz is that powder coating is nice but it chips easily, as I found out again when I caught the gearbox on the rear horns when I removed it to aid the turning of the floor pan on to its side. Also, if applied thickly it is supposed to help with the sound deadening, guess I’ll take those people’s word for it.

I only did the floor underside and the frame head as, in my (uneducated) opinion, they were most likely to take the brunt of the road rash, when this car finally makes on the road. Note, the wooden beam was just a precaution, the whole thing on its side was self supporting with out it. At the front, the track control arm end is through the centre hole of the wheel (wrapped in a cloth) and the anti roll bar is resting on a wooden block.

So this is what I used (above), as before on the beetle body shell inner wings, underside of the engine/gearbox cover and at the front underside. I also got to revisit missed areas of the body shell when I thought I made a good coverage of the floor pan/frame head. Hopefully that will be good enough to withstand various road conditions.

While the compressor and spray stuff was all out and the floor pan was drying I decided to re-apply more primer after the last primer session in April was rubbed down after more filler had been applied and rubbed back again. The end result is much better, it just needs a light rub back and then I will leave it for now to decide if more touch up filler is needed. There is a rust repair to do on the drip rail, just above the drivers door and most of the metal is there, so it will be a filler job.

I am very tempted to get the colour (Clementine L20D) done on the inside… However, I overspent a bit this month on spares, so it will have to wait until next month. The floor pan was dusted down, cleaned up, then covered in dust sheets and rolled back under the 1302 body shell.

Categories
bodywork floor pan suspension

Body work and prep

March 2023 saw me make more progress on the Beetle’s body work by the way of a 3rd or 4th round of filling, sanding and cleaning up with more filler on the original 1997 repairs. I also got to flat off the spot welds around the front cowl at bonnet opening and front valance and I completely removed the wiring loom, replaced with rope guides for the future re-install of a new loom.

The floor pan had been rolled out on to the driveway so it could be cleaned up and where there was the space to attach the anti roll bar with new poly bushes. I had to enlarge the roll bar clamps bolt holes a while ago as I think my original clamps disappeared on the strip down (June 2021) while at Pauls. Fitting the new polyurethane bushes, washer and nut combinations was not as easy as I thought it was going to be. Not enough of the roll bar thread protruded past the poly bushes for the retaining washer and castle nut to get a purchase. So, I had to hit the bushes with a soft mallet to get them pushed in enough to enable me to fit a thinner washer and nut to press the bush in further. I then had to swiftly remove the nut and washer, then quickly put on the large retaining washer and nut to tighten up before the bush expanded again.

I made a short video walk around, however, the audio and commentary isn’t very good, but you should get the idea.

There were a couple of more items to come out of the beetle shell one of which was the wiring loom and I used some rope to attach to an end in the engine bay. This was so I could pull through the rope that would then stay in place for the later re-install of a new wiring loom. The other was the glove box door and I also took off the engine lid hinge mounts to allow easier access to clean up the engine bay firewall.

With 320 grit paper on an orbital sander I sanded the sides of the car shell up to the rain gutter to flatten off the existing paint and remove other minor blemishes. The dashboard was treated the same to flatten off the gloss paint, smooth out minor blemishes and act as a matt surface for, hopefully, better primer adhesion. I also treated the the engine bay firewall the same way and along with a small block with 320 grit sand paper which also cleaned off some the ingrained grease and dirt. I left the ‘tar board’ hooks in place in case I wanted to put one of those back in at a later date.

The next big step is to get some high build primer on the inside and outside of the body. This should highlight the areas requiring more work for filling and rubbing down. It’s a big step and I will be taking my time preparing the workshop to allow me more space to move around the body and masking off areas that won’t need the primer.

Note: no ChatGPT here, all my own words.

Categories
floor pan

Floor Pan is Home

October 2021, and Paul delivered the the floor pan back home. Leading up to this point, I had stripped down the front struts with other steering components in readiness for sending away to be powder coated in the same bright white. I had tinkered with painting the gear lever gloss white but it wasn’t quite the right white when compared with the powder coating bright white and I also touched up the scuffed IRS arms with white Hammerite.

The next part of the plan was to get the brake master cylinder sent away for refurbishment, buy a couple of new flexi brake lines for the rear end with a little more pipe work added and the brake system would be mostly finished except for the front end connections to the front struts. However, with the ongoing body work during November, the budget was draining away and these items would have to go on hold.

Next post, the body.

Categories
pedals suspension

Floor Pan Rebuild

During August I took the opportunity to clean up the gearbox, first by soaking, scraping and scrubbing it with old petrol to loosen the dirt. It was followed by a more detailed clean using a degreaser before finally jet washing.

At the end of August 2021 going in to September, I had some time off work to spend a few days at Pauls Workshop to begin reassembling the components back on to the floor pan. It wasn’t as straight forward as I hoped and felt a little bit out of my depth and Paul was busy with other work but he set me up to use his sand blasting cabinet for most part of my first day. It was quite a fiddley process of which I cleaned up several large nuts, bolts, fastenings and the gear stick components.

1302S floor pan before anything was re-fitted
1302S floor pan before anything was re-fitted
Sand blasting nuts and bolts
Sand blasting nuts and bolts

Progress over the 3 days was slow but I had re-tapped all the threads on the floor pan that had been affected by the powder coating process. Paul fitted a new copper fuel line while I worked on new copper brake lines front to back with cleaned up unions and installed the foot pedals, hand brake with cables and new heater control cables. The heater cable guides needed a proper clean out and Paul devised a method utilising a long thin rod from a roof lining support rod and fitted it to a drill. The result eventually cleared the blockage of sand blasting grit coupled with years of dirt build up. All the other cable guides were treated the same and were all clear.

The powder coating of the floor pan was tested for its durability having got a proper drenching in some September downpours, unfortunately the new brake drums were exposed to this weather and suffered, so had to be cleaned up with a wire brush as they had developed some surface rust in a very short period. After a few Saturdays during September spent with Paul, the floor pan was coming together. Working on the trestles made access much easier to laying out and shaping the brakes lines, hand brake cables and heater cables. One oversight (of a few), there were old bushes in the independent rear suspension arms that hadn’t be removed prior to powder coating and I had bought new bushes to replace them. Unfortunately the new powder coating took a bit of abuse as the arms wouldn’t fit or sit straight in the vice while I had to chisel out the old bushes. It wasn’t easy but I managed it under the guidance of Paul. The rear suspension was set up by Paul and I had asked that it be kept at standard ride height, for now.

For the sharp eyed, the spring plates are up side down in the top left photo and were later swapped over to their correct side. A week after these pictures were taken, the rear hubs were built up with new bearings along with new seals and the brakes (with the cleaned up new drums) rebuilt with new cylinders, brake shoes and fixings.

Nearly there, or so I thought.

Categories
paint

Back from the Powder Coaters

By the end of the month (July 2021) the floor pan and various other parts came back to Paul’s yard, from Blandford Industrial Spraying, looking fantastic in their bright white paint (RAL 9010).

1302S floor pan powder coated new frame head and floor pan
1302S floor pan powder coated new frame head and floor pan
1302S floor pan powder coated floor pan and parts
1302S floor pan powder coated floor pan and parts
Categories
Uncategorized

Restoration – 3rd Attempt

June 2021: It was a warm sunny Saturday when Paul from South Coast Customs & Classics arrived to transport the 1302S Beetle back to his workshop. The plan that day was to separate the body from the floor pan as well as strip down the car some more so the welding on the body and replacement of the frame head could commence.

It turned out to be a lot more difficult than expected with the body being welded to the floor pan in a few locations. Each corner on the rear edge of the floors, each side of bulkhead and on each side of the frame head near the body mounting points. Paul had to cold chisel, angle grind and lever the body and floor apart to break the welds off, though some crumbled due to corrosion. After a fair amount of sweat and effort by Paul the body was ready to be lifted off, quite possibly for the first time in it’s life. Looking at the amount of work Paul had put in to separate the body and floor I was glad he was on board to deal with this, I couldn’t have ever managed that.

With the floor pan now exposed it was clear to see the poor state it was in, even the new floors which were put in 1997 were effectively scrap due to being welded to the body. The frame head had already been identified to be replaced and the “napoleon’s hat” floor pan bulkhead was in a poor state.

I’m not sure if Paul was being kind, but he said it wasn’t the worst beetle he had worked on, which kind of reassured me that this wasn’t going to be too difficult for him to tackle.