Categories
bodywork brakes paint

Summer Jobs 2026

I had been busy on and off with various jobs on the Beetle. The first priority was to finish plumbing in the brake system now that the body was back on. I’ll say it now: fitting the pipework from the brake fluid reservoir to the master cylinder was, so far, probably the most frustrating and awkward job I have had to do on this little car.

From getting the bends in the pipes in the right places, fitting the correct amount of braided rubber hose, to eventually removing the master cylinder so I could push-seat the pipes properly, it was all a bit of a faff. In the end, I assembled around two-thirds of the system on the bench, including the master cylinder, and then made the final connections between the fluid reservoir and the remaining third of the pipework under the car at the bulkhead.

With all the pipework connected, and with some trepidation, I put in the brake fluid. Then some more, and then some more… until I noticed a leak at a joint on the frame head, which I duly tightened up.

I then noticed two large puddles of brake fluid at the rear.

When I first installed the brake lines back in September 2021, I hadn’t tightened them up. So, typically, now that the body was back on, the leaks were in awkward places above the torsion tube, at the ‘T’ joints in the pipes, as well as from both rear bleed nipples. After tussling with the awkward access to the brake-line fittings, I eventually got everything tightened up and the system stopped leaking. The rear brakes, however, still needed adjusting.

Hot weather arrived during May and the next job was to remove the engine tins ready for refurbishment. The only one I couldn’t remove was the panel behind the main crank pulley, as I didn’t have a 36mm socket.

Cleaning the engine tins and ‘doghouse’ fan shroud was a filthy job, covering both myself and much of the workshop in dust. Thankfully, I was wearing a face mask, so I didn’t get too much of it up my nose!

With the tins back to bare metal, I treated them with Jenolite, a rust-converter treatment in an aerosol.

With the hot weather continuing, I decided to turn my attention to the doors, as both needed a bit of attention due to rust appearing along their lower edges. Dismantling them was made much easier after watching a YouTube video by “Slades VW Beetle“. The process was quite straightforward, and with a bit of care it was easy enough to follow the steps in the video.

Stripping the doors back to bare metal was another hot and dirty job, once again plastering the workshop, and everything in it, with a layer of dust. I treated the exposed bare metal with Jenolite, including those awkward-to-reach areas.

There were a few previous rust repairs that I removed, which exposed a few more holes, but thankfully not too many. In fact, the doors were actually in pretty good order. They are clearly replacement doors from a previous restoration, judging by the evidence of their previous colour on the inside panels.

I went to see Paul (and Ash) during this period and, while the main purpose of the visit was to arrange a timeframe for the engine strip-down, I also took the opportunity to get some ideas on repairing the doors.

Welding would have been an option, but not by me! Instead, glass-fibre matting with filler, or glass-fibre filler, would probably suffice. I decided to give the glass-fibre matting a try and bought a small kit from Toolstation. I also heeded the advice Ash had given me about being liberal with the solvent during application.

The results weren’t too bad. It cured quite well and provided a stable surface onto which I could apply some filler to finish things off.

With many of the items cleaned up and ready for painting, the next step was to paint the engine tins, some minor loose components and the doors. However, I only painted the inside panels and door-shut areas of the doors. I plan to paint the outer door panels at the same time as the rest of the body.

Due to the heat, I had some issues with the primer being too thick or coming out too dry. Adding a little more thinners improved the spray pattern. Mindful of this, when it came to applying the colour I added more thinners to the mix to improve the atomisation of the paint.

The final result was OK — good enough for the engine tins and door shuts. I did have to flat back the glovebox door and polish it up, but it eventually looked OK, even though it was a slightly different shade of Clementine L20D orange to the previous batch.

Dash board mainly complete

Categories
bodywork paint painting steering suspension

Front Brakes and Suspension Refit

March 2026: With the body and floor pan finally reunited, I was keen to press on and get the brake lines finished and the front suspension components fitted. Before that though, I wanted to freshen up the front wheel arches so they matched the rears. I still had plenty of the white paint left over from doing the engine bay and rear arches last summer. As always, it took longer to set everything up and clean up afterwards than it did to actually get a decent coat on.

Installing the steering set-up fought me all the way. Initially, there wasn’t enough of the steering shaft protruding to fit the steering wheel, and when I unhitched the column from the universal coupling, there still wasn’t enough length to connect to the steering box. In the end, with the steering wheel fitted and a bit of persuasion from a soft mallet, I eased the column further into its housing until the splined shaft finally met the universal joint on the steering box.

With that small victory, I moved on to fitting the steering tie rods and damper while I still had plenty of room to work.

Fitting the rebuilt front struts was relatively straightforward, although I did have to undo the anti-roll bar mountings to get the lower ball joint seated properly into the track control arms. Once in place, I connected the track rod ends to the steering arms on the struts.

Then came the first “ah” moment — with the wheels on, they were clearly pointing outwards. Not ideal. It turned out the track rod ends hadn’t been wound far enough into the rods, thanks to threads contaminated with sand and grit from the earlier media blasting and powder coating.

1302S Front right side steering components
Front right side steering components, note the tie rod end not wound in very much

So, out it all came again. This time, carefully manoeuvring everything around the now-fitted struts. With the track rods clamped firmly in the vice on the workbench, I worked the ends in and out, cleaning the threads millimetre by millimetre. It took a while, but eventually I had enough adjustment to make a future alignment possible.

Back under the car on the mechanic’s creeper, I went through the now-familiar routine of refitting everything. Thankfully, it wasn’t too arduous this time. Once reconnected, I stepped back — and the wheels were finally pointing forwards.

1302S with front suspension and steering fitted
1302S with front suspension and steering fitted

With that sorted, I turned back to the brakes. I finished fitting the copper lines along the frame head and up to the flexi pipe connections, making the most of the access underneath the car while I still could. Fitting the flexi pipes to the front struts was straightforward, and shaping the copper lines neatly around the lower struts to those freshly rebuilt calipers was a particularly satisfying job.

frame head brake line
frame head brake line

I also dug out the brake fluid reservoir and its associated pipework from storage, only to find the pipes were in poor condition — and one was missing altogether. New ones will need to be made up from 8mm piping.

With the wheels back on, it marked a bit of a milestone — the first time since June 2021 that the car was back on all fours.

Categories
bodywork paint painting seals

Engine Bay Paint and Rubber

At the end of summer the weather was still warm and dry, so I took the opportunity to respray the engine bay in bright white, as before, however this time with successful results. With some fiddling I worked out how to get my spray gun to a correct working pressure and I took extra care of getting my paint mixture right. I took my time spraying three thin, wet coats with 4-5 minute pauses between each coat allowing for it to flash off. I took the opportunity to spray the rear wheel arches to clean them up as well and the result was a fresh glossy finish and finally to my satisfaction.

Another milestone achieved was fitting the engine bay seals that I got from Just Kampers. Fitting of the firewall seal was relatively straight forward, not too much prying or effort required and was done in a bout 20 minutes. The other engine bay rubber was more tricky, though made easier because of the removable rear valance and I could do it in three stages. Rubber gloves, the type used for mechanical work with a pair of large pliers were needed for a good firm grip and vaseline to ease and slide the rubber into the channel. It took about 45 mins to complete.

Categories
bodywork paint painting

Painting – the fifth time

On the Wedenesday I went to visit Paul at South Coast Customs & Classics, however, it turned out I could do him a favour. As I was driving to Charlton Marshal, just outside Blandford, I saw Paul in a bus-stop layby with a very smart blue Beetle with the engine lid open. Luckily there was a bus-stop layby opposite, so I pulled over to see what was going on. The blue Beetle had an ignition failure while on the way to the MOT station and was only 100 metres short of getting there but the garage didn’t want to MOT the car if it couldn’t be driven in. As it happened, I had a tow rope in the boot of my Corsair and offered to get Paul and the Beetle back to his workshop. Once back to the workshop and the Beetle pushed in to the work bay, I got to meet Ash his new work colleague, for the past couple of years.

Categories
bodywork paint painting

Painting the 4th time

I couldn’t help but to mock up with the wings and the removable rear valance, it almost looked like it was nearly there… finished! It did confirm my thoughts that I would need better condition rear wings, but the fronts were OK.

The last paint attempt wasn’t too bad – in most parts I could live with it, but as I was preparing to do the bonnet shuts, front scuttle, front quarter panels and lower parts of the front valence I felt it worth while re-doing the dashboard again as well as digging out the rear valence to paint that too. It turned out to be decision I would regret. Again, various factors at play here from a bad spray gun set up to paint being too ‘dry’ or having too much faith in the fast hardner. Whatever, the paint came out in a spatter (again) and the finish was as expected textured, lumpy orange peel.

I must be glutton for punishment and mockery, its terrible.
This is a portion of the rear valence, takes a brave person to admit to doing this.

So it seems I have a pattern of work, paint on a Sunday, only to rub it all back on the Monday. Well, not the rear valance, thats my sample to show people how bad I am at car spray painting and also gather some advice from folk who know how to paint cars. My next step is to get some advice, salvage the existing paint or buy some fresh paint with standard hardner.

Categories
bodywork gearbox mechanics

Front Valence & Gearbox returns

The front valence had taken something of a beating way back in June 2021 when the body was removed from the floorpan. Now seemed the right time to try and fix it.

First a hammer and dolly was used to sort out the ripples, high spots and dents. A plop of filler, sanded, some primer, smoothed and then a bit more filler, sanded and re-primered. I later applied some colour, which showed up some defects in my filler application but as I will do the paint again, it will serve as a ‘guide’ coat for now.

The gearbox came back from John Walklett Transmissions at the end of May. Fitting wasn’t as straightforward as I thought it would be and aligning the rubber gearbox mounts with the gearbox cradle was a struggle but I got there in the end. All associated components were re-attached and another major step forward made.

Lets have a look how it was 4 years ago, compared to now…

And here is where I got to with the 2nd attempt at applying colour. In fact the finish was worse than my first go, but with out the paint runs and sags. It came out the spray gun as a spatter, probably due to not enough air pressure to atomise the paint more and so the finish was very ‘textured’ much like orange peel. I used rattle can aerosol for around the engine lid mountings and rear air grill under the rear window. The finish came out as a satin finish, much like the white I did inthe engine bay.

Categories
bodywork brakes steering suspension

End of 2024 Update

It’s been a while but once the daily driver cars were sorted, I could recover from the financial strain they put me under and my focus could get on with fixing the Ford Corsair. I resolved the messed up paint job in the Beetle engine bay by using bright white aerosol primer & paint, however, the white wasn’t as glossy as the 2K paint due to being cellulose or acrylic but it will do for now. By November with the Corsair nearly ready for its MOT my attention went back on to the Beetle.

It began with a promo from BCS (Brake Calliper Specialists Ltd) in Nottingham with 25% off all brake calliper refurbishments. I had used them before 5 years ago for the Corsair and they come with a lifetime guarantee so I requested for a quote for refurbishment and painting in the Beetle L20D orange. What they came back with was rather expensive, so I had the quote adjusted for a standard black finish which saved me about £125.00! The total cost was £325.00 including the 25% discount which I thought was still quite expensive but assumed ‘business costs’ had gone up quite a lot since 2019.


For few days over the Christmas holiday I set about reassembling the front struts and noting extra parts required along the way like lower ball joint dust boots, brake lock tabs and strut rubber bump stops. I started with the lower ball joint and removed the split rubber boot and cleaned out the old dirty grease. I also used my Dremel with a low grit sand paper to get the ingrained dirt off the body and get it back to bare metal to then paint it with smooth white gloss Hammerite. The threads were re-tapped to clean them up and then the struts, stub axle & lower ball joint were loosely assembled together. All the minor components like bolts, dust caps and washers were all degreased and cleaned with the Dremel. On the stub axle, the threads for the brake calliper and back plate were all re-tapped after getting a bit contaminated from the powder coating process. They will be assembled properly once the new parts arrive.


The steering arm ball joints were cleaned up re-greased and new rubber dust boots fitted. Fitting the new dust boots was tricky to begin with but once they were secured in a vice it meant I could use both hands and small tipped flat bladed screw drivers to prise the (blue) metal spring clips to hold the new rubber boots in place. The joints were then assembled on to their tie-rod bars, but they too were a bit contaminated from the powder coating and would require a bit more work to screw in freely.

Categories
bodywork mechanics paint

The Setbacks

Since August 2023, it had been a trying time with one thing and another, with all available finances being directed to the daily driver cars. Trying to invigorate motivation over Christmas, I sought to work on cleaning the CV joints and putting on new CV boots. Dismantling the joints was reasonably simple and while messy, not too difficult to clean over a period of days. Ball bearings from one CV joint had signs of wear (a blue-ish tinge) and the other 3 seemed good. However, re-assembly of the good CV joints with their corresponding ball bearing and bearing cages proved to be quite difficult. They wouldn’t just slip back in to place without a bit of force required and then only one of the CV joints remained supple, so I think dismantling and a re-assembly will be on the cards, failing that, I buy a new set of 4 CV joints and be done with it.

Roll around to February 2024 and the mis-haps continued. The weather was nice and I felt I could take on the quick task of respraying the engine bay in bright white to fix the overspray error from last year. Through January over a few weeks I filled some minor holes and gaps in the engine bay area and prepped in readiness for painting.

Set back number 1: I damaged, beyond repair, the new spray gun bought last year by over tightening a BCP coupling.

Set back number 2: In my haste to make do with the other spray gun, I didn’t get my mixing ratios right (hindsight) by misreading the ratios on the measuring cup.

Set back number 3: Because of the messed up ratios the paint was too thin and the spray gun pattern was all over the place. Paint coverage was poor with runs and pooling of the paint, it was time to stop and clean up the mess. Subsequently, the area was later re-rubbed down in readiness for another attempt when I felt confident and ready to tackle it again.

Engine bay rubbed back down after the disastrous attempt at painting
Engine bay rubbed back down after the disastrous attempt at painting
Categories
paint painting

Painting 2K

After watching a few YouTube videos, I gave spray painting a shot in the engine bay around the end of July 2023. I chose bright white (RAL 9010) and used the hardener/activator that came with the primer. I was careful not to use too much, as I thought the primer and hardener were best kept to work together in their specific proportions.

My first try didn’t go so well. I put on too much paint at once and used too high of an air pressure. This resulted in paint running, dripping, and forming pools in the engine bay. I was able to fix it by sanding down the runs, getting rid of the drips, and smoothing out the pooled paint. This got things ready for my second attempt. I also had to apply some primer again on the areas where I had sanded down to bare metal.

Categories
floor pan

Framehead Cover Plate

Just a short update: The frame head had a hole that would need covering. With the availability of 3D printing at my place of work I created a drawing in Adobe Illustrator and passed it to our ‘man’ who then did the necessary work to output to the 3D printer. The end result was a custom framehead blanking plate.