Categories
chit chat

May 2016

Nothing much to see here…

Just look at what I had done and left that engine out on the floor like that since May 2009! It was covered up but it still had 7 years of dampness to spoil it some more. Note the rear end was resting on the gearbox mounting, on an off-cut of an oak gate post, as at some point I needed the substantial car ramps to work on the Corsair [Link Here]. With the help of my growing up and stronger son, we moved the engine into the relatively more shelter of the carport and put it on a pallet. I then wrapped it up some more to protect it from the elements for the unforeseeable future. Also, notice the Capri [Link Here] was still in my possession and would eventually be sold in March 2017, that was a sad day.

Categories
chit chat engine

Dropping the Engine

By May 2009 I had some spare time, money in the bank with the next idea to remove the engine to either strip down or consider a short block replacement. When we bought the car in 1995 we were told of a bottom end knock which was either crankshaft bearings or the big ends needed replacing. With the rear end jacked up and the car on our substantial ramps removal of the engine wasn’t as difficult as I remember, four bolts, bit of a jiggle on to the trolley jack and it was out…

The following month the money set aside for a replacement block was spent on a refurbished gearbox for the daily driver Passat. In hindsight – it was probably just as well because no more was done to the little car for some time.

Categories
bodywork chit chat pedals

Runners and Pedals

The financial situation had eased which helped fire up the enthusiasm with the Beetle in the spring of 2008. The covers were removed to reveal the Beetle was fairing well in the car port under a tarpaulin. At some point, Grey zinc primer had been applied to the surface rust that was appearing on the repairs done in 1998.

A pair of correct style seat runners were purchased as the new floor that had be done 10 years previously had the wrong type. I also bought a new accelerator and clutch cable as well as some foot pedal spare parts. There is not any photo graphic evidence, but I replaced the seat runners by drilling out the spot welds on the existing runners and successfully welding in my new ones. My welding had improved (albeit some what agricultural) since 1996, as I had built this dragster for my then young son for a carnival.

By early summer 2008 and I had the foot pedals with other associated parts powder coated in readiness for installation. The powder coater had unfortunately painted over some areas that needed to be clear of paint and a fair bit of rubbing down was required so it would all fit together and operate smoothly. Installation was tricky but I had to drill holes in the new floor to weld captive nuts on the underside so I could bolt down the mounting bracket for the whole assembly. I welded the accelerator pedal bracket to the floor, it was not pretty but functional. Fitting the clutch cable was nigh on impossible even with guidance in the Beetle bible (How To Keep Your Volkswagen Alive) so I left that for another time.

Categories
chit chat

Summer 2000

Nothing happened to the Beetle… Only that we had to move it from the lock up as the group of garages was to be sold and the land developed in to housing. In the summer of 1999, we had moved house to a place with scope to accommodate off road parking and extra garaging. The move of the Beetle ensured we had to get on with the plan and in the summer of 2000 we built a double carport in the garden. Note: you can see our trailer we used to haul the beetle about – I think we used it about 4 times, but got our moneys worth when we sold it on.

For the next seventeen years the Beetle and Capri were carport companions, I sold the Capri (2.8 Injection Special) in 2017.

Categories
Uncategorized

Professional Help

A year later, Autumn 1997, we had the finances to take the Beetle to seek a professional and were directed to a chap known as Mike the Welder, who was taking over a former VW specialist garage on the Wimborne Road in Bournemouth. Buoyed by his no problem approach and promising to keep his current rates for the project he took it on as his first car at the new premises, now renamed as Small Car Projects, in October 1997. Mike and a member of his team worked on the Beetle on and off through to the November of 1997. New front inner arch panels left and right, rear lower quarter repair panels left and right, new right hand floor, new half left hand floor, new lower A post panel repairs left and right and rear floor repairs right side were done.

Mike kept the car over the winter as he identified that it would be easier to replace the spare wheel well and front valence rather than repair the accident damage. We needed to save up a bit more cash in that time. By March 1998 the front end had been replaced with new panels and the beetle was delivered back to our lock up. Mike had assured us all was good with the body and that it could be removed from the floor if needed in the future. We were happy and it looked like a good job had been done.

Other life events took over from mid 1998 and the Beetle lay dormant in the garage until it had to be moved in the Summer of 2000.

Categories
bodywork Buying chit chat

The Resto Begins

Back in August 1995, at our rented garage (lock up), the wife and I had stripped the car down so we could assess the way forward. It had become apparent that a few more welding jobs would be needed. By the summer of 1996 I had been preparing to work on the Beetle so had purchased a SIP350 Turbo welder, associated accessories and sheet metal to tackle the body work that required repair. Some new panels comprising of a semi-W engine lid, matching rear valance and a pre ’67 front valance had been purchased to fire the imagination from URO in Bournemouth. We had also purchased a small car trailer to move the Beetle about.

newspaper stuffed in the ‘A’ posts

We took the beetle around to my ‘in-laws’ home to work on in their garden as they had a fair amount of space and it was easier to get electric to as well. A closer inspection was revealing a myriad of issues of old repairs over old repairs and in dire need of repair. It’s true, I found newspaper stuffed in the ‘A’ posts from an Essex publication after I had chipped away a bodge of filler around the lower door hinges, on both sides. A DVLA vehicle history search, that I later obtained, revealed it had spent some time in Billericay, Essex in the mid 1970s.

It didn’t occur to me to seek repair panels for these sections, being the complete novice at this body work business I was trying to make my own patches out of sheet metal. I took instruction from various members of the family trying out my new MIG welder but I was mainly blowing holes in the bodywork and new steel creating a fair amount of spatter welding. The advice being dished out wasn’t really helping me make a decent job of this and my patch work of repairs were bloody awful. I was too afraid of cutting too much out and ruining the structural strength of the vehicle.

The end of that week in August 1996, I became very aware I had bitten off more than I could chew on this project and the car was wheeled away and put back into it’s garage for another long stint of storage.

Categories
Buying chit chat

The Beginning

August 1995 and the decision to buy a classic car to ‘do up’ was made. I was looking at another Ford, a Mk3 Cortina 2000E but my wife wasn’t sure, as this would be the car for her to take long to classic car shows while I had my Ford Capri 2.8i. A VW Beetle was advertised in a local newspaper with “good body work/spares or repair – £495”. Upon inspection it was revealed as a MOT failure with an engine issue so we paid £450. I was satisfied that this 1302S Beetle (registered 4 November 1970) was within my capabilities, with the two marked up areas of welding and the engine requiring a rebuild due to a knocking from the bottom end, those tones of “its a Beetle, they’re easy to work on” rang around in my head. At the very least it was driveable and it managed the 5 mile trip home without any problems. The 1302S Beetle did look good overall, though my naivety was evident when we were to take the car apart later.

“good body work/spares or repair – £495”

The following week we discussed our plans with the car and the way we wanted it to look. Scouring various back issues of Street Machine magazines we were thinking of a mild roof chop 😮, welding wings to the body, smoothing and de-seaming, de-guttering, shaving door handles, hidden door hinges, frenched lights, lowered by Rayvern Hydraulics and big wheels. This was all before we had even taken it apart. I was also thinking in making it look more like an early Beetle (pre ’67) with the long nose bonnet and ‘W’ deck lid.

With a bank holiday weekend at our disposal my wife and I set to on the Beetle by removing the bumpers, wings and running boards to take a closer look at the body work. It wasn’t looking very good, a multitude of previous repairs and corrosion that needed attention began to distract me from our original plans. By the Autumn other things in life had taken over and the Beetle was side-lined and stored in the lock up until the following year. In the meantime, I made up a ‘Photoshop’ mock up of the plan around this time to help push the ideas of the project along.

Animated GIF of the original ‘Photoshop’ version done in 1995/96