{"id":2076,"date":"2025-01-19T15:19:33","date_gmt":"2025-01-19T15:19:33","guid":{"rendered":"https:\/\/domcoleman.co.uk\/Blog\/?p=2076"},"modified":"2025-01-19T15:55:07","modified_gmt":"2025-01-19T15:55:07","slug":"where-did-2024-go","status":"publish","type":"post","link":"https:\/\/domcoleman.co.uk\/Blog\/where-did-2024-go\/","title":{"rendered":"Where did 2024 go?"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">It\u2019s early December as I write this, and I\u2019m reflecting on the saga of fixing up the daily drivers last autumn. The issues that began in September 2023 finally wrapped up in March this year, leaving my finances (and sanity) thoroughly drained. As a result, work on the Corsair and the VW Beetle [<a href=\"https:\/\/domcoleman.co.uk\/1302s\/\" data-type=\"link\" data-id=\"https:\/\/domcoleman.co.uk\/1302s\/\">LINK<\/a>] had to take a back seat until summer 2024.<\/p>\n\n\n\n<!--more-->\n\n\n\n<h2 class=\"wp-block-heading\">August<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">I\u2019d arranged for John Midwood to sort out the Corsair\u2019s steering box chassis mounting, which had been flexing alarmingly. Sadly, I don\u2019t have any photos of the process, but John reassured me that the original repair on the inner chassis was decent\u2014he just tidied it up a bit. The real work happened in the front offside wheel well, where corrosion had thinned the metal and caused the flexing. John cut out the offending area and welded in a fresh section, blending it in seamlessly. To beef up the steering box mounting, he noted that Ford had added a W-shaped metal bar behind the bolt holes in the chassis leg. By early September, the flexing issue was history, leaving the rear brake cylinders next on the list.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">October<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Back in the summer, I\u2019d picked up two new rear brake cylinders and a master cylinder repair kit from Mev Spares (see Thanks), ready for the challenge. It had been ages since I last tackled drum brakes, so I took my time, keeping everything as clean and organised as possible. Removing the brake drums turned out to be the trickiest bit\u2014especially since I\u2019ve dropped one on my fingers before (lesson learned!). The offside cylinder was well and truly seized and had probably been that way for ages. I also had to replace a small section of brake pipe, as the union was stuck fast in the old cylinder. While I was at it, I gave the master cylinder a fresh set of seals\u2014the last overhaul was all the way back in <a href=\"https:\/\/domcoleman.co.uk\/Blog\/brake-master-cylinder-refurb-again\/\" data-type=\"link\" data-id=\"https:\/\/domcoleman.co.uk\/Blog\/brake-master-cylinder-refurb-again\/\">April 2020<\/a>.<\/p>\n\n\n\n<figure class=\"wp-block-gallery has-nested-images columns-2 is-cropped wp-block-gallery-1 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125418.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"576\" height=\"1024\" data-id=\"2081\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125418.jpg\" alt=\"A stripped down offside rear brake drum on a Ford Corsair, English Axle\" class=\"wp-image-2081\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125418.jpg 576w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125418-169x300.jpg 169w\" sizes=\"auto, (max-width: 576px) 100vw, 576px\" \/><\/a><figcaption class=\"wp-element-caption\">A stripped down offside rear brake drum on a Ford Corsair, English Axle<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125432.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"576\" height=\"1024\" data-id=\"2079\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125432.jpg\" alt=\"Rear nearside rear hub with brake assembly removed\" class=\"wp-image-2079\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125432.jpg 576w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125432-169x300.jpg 169w\" sizes=\"auto, (max-width: 576px) 100vw, 576px\" \/><\/a><figcaption class=\"wp-element-caption\">Rear nearside rear hub with brake assembly removed<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125404.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" data-id=\"2080\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125404.jpg\" alt=\"Brake master cylinder fitting new seals\" class=\"wp-image-2080\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125404.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125404-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241026_125404-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Brake master cylinder fitting new seals, again<\/figcaption><\/figure>\n<\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">After most of the day wrestling with the brake system, it was time for the final job: bleeding the brakes. I\u2019d bought a Gunson Easy Bleed kit but quickly discovered the pressure cap didn\u2019t fit my master cylinder. Plan B involved my trusty Mitivac pump and some good old-fashioned footwork from my son. Unfortunately, I botched the bleed process, which became painfully obvious on the test drive!<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">November<\/h2>\n\n\n\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123645.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"576\" height=\"1024\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123645.jpg\" alt=\"clutch slave cylinder mounting on gearbox bell housing\" class=\"wp-image-2084\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123645.jpg 576w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123645-169x300.jpg 169w\" sizes=\"auto, (max-width: 576px) 100vw, 576px\" \/><\/a><figcaption class=\"wp-element-caption\">clutch slave cylinder mounting on gearbox bell housing<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Next up was the leaky clutch slave cylinder, which was brand-new in December 2012 and fitted in <a href=\"https:\/\/domcoleman.co.uk\/Blog\/the-clutch-works\/\" data-type=\"link\" data-id=\"https:\/\/domcoleman.co.uk\/Blog\/the-clutch-works\/\">July 2014<\/a>. I still remember the <a href=\"https:\/\/domcoleman.co.uk\/Blog\/unseizing-the-clutch-part-2\/\" data-type=\"link\" data-id=\"https:\/\/domcoleman.co.uk\/Blog\/unseizing-the-clutch-part-2\/\">nightmare of removing the old<\/a> one back then, but this time, with the car on ramps, it was much easier. Decent circlip pliers made quick work of removing the retaining clip, and stripping down the cylinder to replace the seals was a straightforward affair. Refitting was smooth sailing, and bleeding the system went well too. My son lent a hand again, helping me adjust the rear brake shoes for a better handbrake and re-bleeding the brakes properly this time. Success at last!<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123524.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123524.jpg\" alt=\"Corsair V4 - Clutch slave cylinder\" class=\"wp-image-2083\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123524.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123524-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2024\/12\/20241117_123524-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Corsair V4 &#8211; Clutch slave cylinder<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Then there was the rear exhaust box\u2014a 24-year veteran of the car, and not about to go quietly. I soaked it repeatedly with WD-40 over a couple of days, then attacked it with a Dremel and a cold chisel. Slowly but surely, I peeled the stubborn pipe away. After yet more WD-40 and a two-day wait, the pipes finally came apart. This was now late November and the rear exhaust box was off and ready for its trip to <a href=\"https:\/\/www.maniflow.co.uk\">Maniflow<\/a> exhaust specialists in Salisbury.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">December<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">While waiting for the rear exhaust section to be made, I took the opportunity to adjust the tappets over the Christmas holiday. Ever since I last did them in <a href=\"https:\/\/domcoleman.co.uk\/Blog\/tappets-and-tidy\/\" data-type=\"post\" data-id=\"662\">July 2016<\/a>, there\u2019d been a slight, annoying \u201ctappety\u201d noise\u2014not nearly as bad as before, but still enough to bug me. After more than 5,000 miles of motoring adventures, it seemed about time for an adjustment.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">I set the tappets with the engine cold, but since the exhaust was off, I decided against starting the car. I figured I\u2019d wait until the new exhaust was fitted before tackling the warm engine adjustments. No point disturbing the neighbours with a racket, right?<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">January 2025<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.maniflow.co.uk\">Maniflow<\/a> in Salisbury did a fantastic job replicating the old exhaust box, pipes, and bracket. They even offered to paint it as part of the cost if I\u2019d asked, but I decided to handle that myself. Over a few days, I gave it several coats of silver Hammerite Smooth from a trusty rattle can. The finish looked great, and it felt good knowing it had plenty of protection.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Fitting the new exhaust was surprisingly straightforward. I\u2019d bought new rubber hanger loops and an exhaust clamp from <a href=\"https:\/\/www.carbuilder.com\">Car Builder Solutions<\/a>, so everything went together without a hitch.<\/p>\n\n\n\n<figure class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-2 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193139.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" data-id=\"2099\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193139.jpg\" alt=\"Ford Corsair rear exhaust section looking worse for wear\" class=\"wp-image-2099\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193139.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193139-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193139-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Ford Corsair rear exhaust section looking worse for wear<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193126.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" data-id=\"2100\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193126.jpg\" alt=\"Rear exhaust pipe section join proving difficult to separate\" class=\"wp-image-2100\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193126.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193126-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20241125_193126-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Rear exhaust pipe section join proving difficult to separate<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250113_160815.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" data-id=\"2096\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250113_160815.jpg\" alt=\"Old and new rear exhaust silencer boxes\" class=\"wp-image-2096\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250113_160815.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250113_160815-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250113_160815-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Old and new rear exhaust silencer boxes.<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250114_192603.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"576\" height=\"1024\" data-id=\"2098\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250114_192603.jpg\" alt=\"Smooth Hammerite painted rear exhaust &amp; silencer\" class=\"wp-image-2098\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250114_192603.jpg 576w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250114_192603-169x300.jpg 169w\" sizes=\"auto, (max-width: 576px) 100vw, 576px\" \/><\/a><figcaption class=\"wp-element-caption\">Smooth Hammerite painted rear exhaust &amp; silencer <\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250119_100815.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"576\" data-id=\"2095\" src=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250119_100815.jpg\" alt=\"Ford Corsair rear exhaust section fitted\" class=\"wp-image-2095\" srcset=\"https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250119_100815.jpg 1024w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250119_100815-300x169.jpg 300w, https:\/\/domcoleman.co.uk\/Blog\/wp-content\/uploads\/2025\/01\/20250119_100815-768x432.jpg 768w\" sizes=\"auto, (max-width: 767px) 89vw, (max-width: 1000px) 54vw, (max-width: 1071px) 543px, 580px\" \/><\/a><figcaption class=\"wp-element-caption\">Ford Corsair rear exhaust section fitted<\/figcaption><\/figure>\n<\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">However, with the cold and damp weather lingering, I held off on connecting the battery and starting the Corsair. I\u2019m saving that for a warmer, drier day\u2014when I\u2019ll finally warm up the engine and fine-tune those tappets. Until then, it\u2019s back to the house for a cup of tea to warm up and some planning for the next job!<\/p>\n","protected":false},"excerpt":{"rendered":"<p>It\u2019s early December as I write this, and I\u2019m reflecting on the saga of fixing up the daily drivers last autumn. The issues that began in September 2023 finally wrapped up in March this year, leaving my finances (and sanity) thoroughly drained. As a result, work on the Corsair and the VW Beetle [LINK] had &hellip; <\/p>\n<p class=\"link-more\"><a href=\"https:\/\/domcoleman.co.uk\/Blog\/where-did-2024-go\/\" class=\"more-link\">Continue reading<span class=\"screen-reader-text\"> &#8220;Where did 2024 go?&#8221;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[21,6,5,4,29,17],"tags":[32],"class_list":["post-2076","post","type-post","status-publish","format-standard","hentry","category-body-chassis","category-brakes","category-clutch","category-engine","category-exhaust","category-steering","tag-ford-corsair"],"_links":{"self":[{"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/posts\/2076","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/comments?post=2076"}],"version-history":[{"count":17,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/posts\/2076\/revisions"}],"predecessor-version":[{"id":2118,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/posts\/2076\/revisions\/2118"}],"wp:attachment":[{"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/media?parent=2076"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/categories?post=2076"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/domcoleman.co.uk\/Blog\/wp-json\/wp\/v2\/tags?post=2076"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}